Kevin Horton
Well Known Member
I'm looking for advice on resolving a recurring problem with exhaust pipe cracks. I've got a Lycoming IO-360-A1B6 engine on an RV-8. The exhaust is by Vetterman, purchased in 2001. Originally it was mounted with the tail pipes supported from the engine mount, as recommended by Larry Vetterman at the time the exhaust was purchased. After the second time that an Adel clamp broke, I replaced the pipe and rubber pieces with springs, copying the idea from the way exhausts are supported on Mooneys.
The first major problem was in 2011, on the way home from Oshkosh, with 136 hours on the aircraft - the #3 exhaust pipe broke completely off at the flange at the top. Luckily we were right overhead CYYB airport, so we landed there without incident. We rented a car and drove four hours to get home. I sent the exhaust back to Vetterman for repair. Larry said that the IO-360-A series engines on the RV-8 had been his most problematic engine/aircraft combination, and that he had made many detail design changes since my exhaust was shipped, as exhausts returned for repair showed where the problem areas were. Larry and Clint replaced the top part of the #3 pipe with a thicker wall piece, and made a few other changes to put the system in a configuration that was close to the current shipping exhausts.
In July 2012, with 197 hours on the aircraft, I discovered that the exhaust was cracked in the Y that joins the pipes from #3 and #4 cylinders. It was sent back to Vetterman for repair. Note that I also discovered metal in the oil filter at that time, and the engine was found to have cam lobes that were wearing. It is possible that the cylinders were not all producing equal amounts of power, leading to more vibration than normal. When remounting the repaired exhaust, I changed the exhaust mounting to hang it off the back of the oil sump, as per current recommendations.
A week ago, with 241 hours on the aircraft, I discovered a significant crack at the weld at the flange on the #3 pipe. There wasn't time to ship it back to Vetterman Exhaust in SD, and get it back before Oshkosh, so I had it welded locally. I'll treat this as a temporary repair, and will either ship it back to Vetterman for a proper repair after returning from OSH, or replace the whole exhaust system with a new one.
Given that I have had three significant exhaust cracks in 240 hours of flying, something is clearly amiss. I see the following possibilities, in no particular order:
I really want a more reliable exhaust, so I can travel without worrying about it. After getting back from Oshkosh, I'll call Vetterman Exhaust to get their thoughts on why my aircraft is getting these frequent cracks, and how best to avoid them in the future.
I'm considering ordering a brand new exhaust system. That will avoid missing several weeks of summer flying while having Vetterman rebuild my orginal one, it'll give me a system in the latest configuration, and I'll have the original one as a spare system in case the new one ever cracks. I'll also make a point of pulling the cowling more often and won't put it back on until I've ensured the ball joints are moving freely. I'm not sure what inspection interval will be required so that the ball joints don't seize between inspections. I'll start with a fairly short inspection interval, and gradually increase it.
Questions:
The first major problem was in 2011, on the way home from Oshkosh, with 136 hours on the aircraft - the #3 exhaust pipe broke completely off at the flange at the top. Luckily we were right overhead CYYB airport, so we landed there without incident. We rented a car and drove four hours to get home. I sent the exhaust back to Vetterman for repair. Larry said that the IO-360-A series engines on the RV-8 had been his most problematic engine/aircraft combination, and that he had made many detail design changes since my exhaust was shipped, as exhausts returned for repair showed where the problem areas were. Larry and Clint replaced the top part of the #3 pipe with a thicker wall piece, and made a few other changes to put the system in a configuration that was close to the current shipping exhausts.
In July 2012, with 197 hours on the aircraft, I discovered that the exhaust was cracked in the Y that joins the pipes from #3 and #4 cylinders. It was sent back to Vetterman for repair. Note that I also discovered metal in the oil filter at that time, and the engine was found to have cam lobes that were wearing. It is possible that the cylinders were not all producing equal amounts of power, leading to more vibration than normal. When remounting the repaired exhaust, I changed the exhaust mounting to hang it off the back of the oil sump, as per current recommendations.
A week ago, with 241 hours on the aircraft, I discovered a significant crack at the weld at the flange on the #3 pipe. There wasn't time to ship it back to Vetterman Exhaust in SD, and get it back before Oshkosh, so I had it welded locally. I'll treat this as a temporary repair, and will either ship it back to Vetterman for a proper repair after returning from OSH, or replace the whole exhaust system with a new one.
Given that I have had three significant exhaust cracks in 240 hours of flying, something is clearly amiss. I see the following possibilities, in no particular order:
- Excessive vibration - I don't perceive that the engine vibrates any more than other Lycomings, but maybe I'm wrong. I flew big radials for a few years early in my career (S-2 Trackers) so perhaps I am not as sensitive to vibration as some other people. I usually cruise LOP, and all four EGTs peak in a band of 0.1 to 0.2 GPH fuel flow, so I don't think vibration from lean running should be the issue. I'm not sure what the best way is to objectively determine whether my engine has excessive vibration though. Comments?
- Poor maintenance - every time I check the exhaust system I find the ball joints seized up. Sometimes I manage to get them freed up by using Mouse Milk, but sometimes I have given up.
- Previous damage - the aircraft had a significant engine overspeed during the early flight testing (almost 4000 rpm). Maybe that event somehow stressed the exhaust system, and later cracks are a delayed result.
- Quality control issue with exhaust system - I know that most people have pretty good service history from Vetterman exhausts, but maybe I've got a bad one.
I really want a more reliable exhaust, so I can travel without worrying about it. After getting back from Oshkosh, I'll call Vetterman Exhaust to get their thoughts on why my aircraft is getting these frequent cracks, and how best to avoid them in the future.
I'm considering ordering a brand new exhaust system. That will avoid missing several weeks of summer flying while having Vetterman rebuild my orginal one, it'll give me a system in the latest configuration, and I'll have the original one as a spare system in case the new one ever cracks. I'll also make a point of pulling the cowling more often and won't put it back on until I've ensured the ball joints are moving freely. I'm not sure what inspection interval will be required so that the ball joints don't seize between inspections. I'll start with a fairly short inspection interval, and gradually increase it.
Questions:
- other than ordering a new exhaust, is there something else I should consider doing instead?
- if I order a new exhaust, is Vetterman still the best bet, or is there another supplier I should look at?
- if Mouse Milk the best anti-seize for the ball joints, or is a better product?
- has anyone else had recurring exhaust system issues? If so, did you manage to resolve them?