VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 08-30-2017, 07:21 AM
maus92 maus92 is offline
 
Join Date: Nov 2013
Location: Annapolis MD
Posts: 307
Default Upgrades at CI

I'm coming up to October when my condition inspection is due. I'm toying with the idea of doing some of the upgrades that are on my list:

1. Smoke System
2. Replacing Cleveland wheels & brakes w/ Grove - for better stopping power
3. P-Mag
4. GTN650
5. Paint

They are listed in order of cost, and not necessarily desire

- If I were to do the wheels, should I go with magnesium or aluminum for the mains, and tube or tubeless for the nose wheel (optional)?

- Would the P-Mag make a big difference on an O-360? The Slicks have about 400hrs, and I'm beginning to see a larger drop on the left / impulse mag.
__________________
CA
2000 RV-8A | O-360, FP, G3X Touch, VP-X, EarthX
Eastern Shore | KESN
Reply With Quote
  #2  
Old 08-30-2017, 10:54 AM
Carl Froehlich's Avatar
Carl Froehlich Carl Froehlich is offline
 
Join Date: Dec 2007
Location: Dogwood Airpark (VA42)
Posts: 1,031
Default

Dual pMags will make a noticeable improvement in starting and reduction of cruise LOP fuel burn. My new engine from Lycoming will arrive in a week or so with one pMag installed, and the other hole empty but prepped for the second pMag. I have 700 flawless hours on dual pMags in an 8A and consider this one of the best values out there.

I have 400 hours (much of it IFR time) behind the GTN-650 in the RV-10 and will not install it in the new RV-8 project. Instead I will be installing the Avidyne IFD550. The IFD550 is about the same cost as the GTN-650 (ignore the list prices). The GTN-650 works but is clunky and way too much button smashing to do routine stuff. That and my GTN-650 arrived with two "known" problems that I had to fix on my dime, then a hard failure. All in the first 12 months of service (but after the warrantee period that started after purchase). Recommend you call Rob Hickman at Advanced Flight Sytems to discuss.

Carl
Reply With Quote
  #3  
Old 08-30-2017, 10:58 AM
Pat Hatch's Avatar
Pat Hatch Pat Hatch is offline
 
Join Date: Jun 2006
Location: Vero Beach, FL
Posts: 762
Default

Charley, I can give you my experience with converting from Cleveland to the Grove brakes. The dual caliper arrangement of the Groves will require you to glass in a small "bump" in the wheel pants to accommodate the lower caliper. Not much of a bump, and it's barely noticeable, but will require some glass work and repainting. The difference in stopping power is significant. I was warned about a possible nose over, but I think these concerns are overblown.

I went with the aluminum wheels and the Airstop tubes. Have had the Groves now for a couple of years and they've been perfect.

EDIT: Oops, you have an 8A, disregard the comment about nose over!
__________________
Pat Hatch
RV-4 (Gone to RV heaven)
RV-6 (N44PH - Flying)
RV-7 (Sold)
RV-8 (Helped build Bob Lund's airplane)
www.phaviation.com Trim Relay Boards/Wiring Hubs
www.pathatch.com/blog (Photography)
Track Me

Last edited by Pat Hatch : 08-30-2017 at 11:03 AM.
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 02:02 PM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.