VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics


Go Back   VAF Forums > Model Specific > RV-10
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 12-01-2013, 07:11 PM
bpattonsoa bpattonsoa is offline
 
Join Date: Apr 2005
Location: Indepenence, Oregon
Posts: 286
Default Outboard mid Seat bracket

Are there any -10s flying with four bolts in the outboard mid seat bracket? Especially the rear outboard bolt?

Thee other three are the worst in the airplane to date, even with the bolt in from the bottom. The last SOB won't go in that way and I am not sure a nut will fit in that #%|\#% corner.

As a Licensed Engineer I am about ready to declare that bolt as part of my structural margin and leave it in the box!
__________________
Bruce Patton
Building Rans S-20 Raven 796S reserved
Going to the light side!
RV-6A 596S flying since '99 (Sold)
HP-18 5596S flying since '89
RV-10 996S tail, quick build wing and slow build fues., - dual Skyviews with complete system, two radio and not much else. Interior completely finished with Zolatone. CF plenum, interior complete. 1624 lbs, FLYING after a 21.5 month build.
Reply With Quote
  #2  
Old 12-01-2013, 07:13 PM
Mike S's Avatar
Mike S Mike S is offline
Senior Curmudgeon
 
Join Date: Sep 2005
Location: Dayton Airpark, NV A34
Posts: 14,386
Default

I could not get those bolts in, but my wife (with her much smaller and more flexible hands ) was able to do so.

They are a PITA for sure
__________________
Mike Starkey
VAF 909

Rv-10, N210LM.

Flying as of 12/4/2010

Phase 1 done, 2/4/2011

Sold after 240+ wonderful hours of flight.

"Flying the airplane is more important than radioing your plight to a person on the ground incapable of understanding or doing anything about it."
Reply With Quote
  #3  
Old 12-01-2013, 07:20 PM
9GT's Avatar
9GT 9GT is offline
 
Join Date: Jan 2010
Location: Southern Michigan
Posts: 1,521
Default

It will fit and I would recommend that you put it in. Like Mike say's, small hands are a help. IIRC, I super glued the washer to the nut, then taped that to a welding wire I bent to get it started. Took me about 3-4 hours to get both sides done and tightened.
__________________
David C.
Howell, MI

RV-9A: Under Construction. N161RV (Reserved)
RV-10: N959RV Completed 12/29/2013 SOLD 08/23/2016

"Donor Exempt" but donated through Dec. 2018
Reply With Quote
  #4  
Old 12-01-2013, 07:27 PM
eric.kallio eric.kallio is offline
 
Join Date: Aug 2006
Location: Prairieville, LA
Posts: 118
Default A real PITA

Been quite awhile since I did it but this was a task that stood out and I still remember a little about it. I used a couple dabs of RTV to secure the washer to the nut. Then put a piece of tape over one side of a combination wrench. The nut/washer was then held into the wrench while I twisted, turned, and basically deformed my arm to reach the bolt. It worked, but I still had to tighten the bolt head and not the nut so I secured it backwards, but I am willing to accept that.

Eric
__________________
Eric Kallio
RV-10
N518RV... Flying

Last edited by eric.kallio : 12-01-2013 at 07:59 PM.
Reply With Quote
  #5  
Old 12-01-2013, 08:09 PM
N427EF N427EF is offline
 
Join Date: Oct 2005
Posts: 1,510
Default Lot o' cussing!

Sorry to say, those bolts stretched my vocabulary to the limit where I not on
recited profanity in 2 languages and added the words that I had not yet learned just to be sure the episode was not understated.
Some combination of what has been said worked in the end and now I really enjoy those seats.
Good luck!
__________________
Ernst Freitag
RV-8 finished (sold)
RV-10 Flyer 400 plus hours
Over 2500 Gallons of E10 mogas burned
Don't believe everything you know.
Reply With Quote
  #6  
Old 12-01-2013, 09:48 PM
Jackm Jackm is offline
 
Join Date: Feb 2012
Location: Prosser,WA
Posts: 272
Default Just completed a day ago

Sorry...found them a bit of a challenge but not bad at all...Lift each bolt up, slide nut and washer in place and drop bolt down and thread bolt into nut. Tighten with offset wrench and stubby 1/4 inch drive from top. Happy Happy
__________________
Jack Maljaars
Rv10
N819DJ flying. 350hrs +
Dues 2015 pd
Reply With Quote
  #7  
Old 12-01-2013, 10:39 PM
BobTurner BobTurner is offline
 
Join Date: Dec 2011
Location: Livermore, CA
Posts: 5,402
Default

Challenging but I got all four in.
Reply With Quote
  #8  
Old 12-01-2013, 11:05 PM
Wayne Gillispie Wayne Gillispie is offline
 
Join Date: Apr 2009
Location: USA
Posts: 1,494
Default

Was this before or after the doors. That is the only problem area that I can recall.
__________________
Good judgment comes from experience, and a lot of that comes from bad judgment.
Reply With Quote
  #9  
Old 12-02-2013, 01:44 AM
kiwipete kiwipete is offline
 
Join Date: Oct 2007
Location: Birmingham United Kingdom
Posts: 367
Default Magnet

Another option is to hold the washer and nut in place is to put a small magnet on the bolt head. The washer and nut will then be drawn onto the bolt. Works well.
Or I use my magnet on the end of my inspection mirror to hold the washer and nut and then position into place.
I'm lucky I have small hands. But enlisting some help from a younger person is not a bad idea.
I remember reading the horror stories but guess I was lucky and each one only took a few minutes.

Good luck

Peter
__________________
RV7 G-PBEC Flying
RV10 Finishing
Reply With Quote
  #10  
Old 12-02-2013, 02:43 PM
Flandy10 Flandy10 is offline
 
Join Date: Dec 2007
Location: Peachtree City, GA
Posts: 119
Default Outboard mid seat rail support

One suggestion-- before tightening down the bolts, check that the seat rail holes line up correctly with the support in place.

I had both supports in place for awhile and then found out that despite being CAD designed, they did NOT line up with the seat rails . If you think putting them in is a PITA, try taking them out to fix them and reinstalling them TWICE . And yes, I had installed them correctly. My initial installation was checked and verified by a repeat Rv-10 builder and local DAR.

My solution was to slot the support mounting holes and trim off the entire back flange for clearance off the main spar bolts.
__________________
Scott Flandermeyer
Rv-10 TDI #40816
Fayettevile, GA

2018 VAF Donation complete
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 03:58 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.