VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics


Go Back   VAF Forums > Model Specific > RV-12
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 10-21-2018, 07:34 AM
rolick22's Avatar
rolick22 rolick22 is offline
 
Join Date: Oct 2013
Location: Powell, OH
Posts: 115
Default Garmin AP Roll Pushrod too Short for iS installation

The pushrod that I made (5 1/4 inch) IAW 44B-02 dated 4/02/14 does not appear to be the correct length for the iS installation. I have tried to install the AP servo with the rod end this way but it is way to short. The stick is approximately in the neutral position. Guessing the geometry is a little different then the original ULS installation with the manual flap handle. I know there is no avionics plans yet available for the iS but maybe someone knows if the length of the pushrod for iS installation is different or the same. I have double check the rod length of all the other push rods and they check out good.

__________________
_____________________________________________
David Rohrlick
PPSEL A&P
RV-12 Finished (Empennage, Fuselage(1st gen), and Wing kit)
Empennage finished (need to add the panel cut out)
Wings finished (need to add the left landing light)
iS Finishing Kit In work
iS Fuselage Finished
1st GEN FUSELAGE SOLD
Serial#12-0864
N864DR Reserved
Reply With Quote
  #2  
Old 10-22-2018, 07:40 PM
rolick22's Avatar
rolick22 rolick22 is offline
 
Join Date: Oct 2013
Location: Powell, OH
Posts: 115
Default Update GSA 28 Push Rod on the iS

Update on anyone doing Garmin

__________________
_____________________________________________
David Rohrlick
PPSEL A&P
RV-12 Finished (Empennage, Fuselage(1st gen), and Wing kit)
Empennage finished (need to add the panel cut out)
Wings finished (need to add the left landing light)
iS Finishing Kit In work
iS Fuselage Finished
1st GEN FUSELAGE SOLD
Serial#12-0864
N864DR Reserved
Reply With Quote
  #3  
Old 10-23-2018, 12:46 PM
subpar_bucker subpar_bucker is offline
 
Join Date: Oct 2016
Location: Cranberry Twp, PA
Posts: 20
Default

Here I was all impressed that you had ordered your 12iS compatible avionics kit! I keep waiting for the announcement of when those will be available!
Reply With Quote
  #4  
Old 10-23-2018, 09:30 PM
rolick22's Avatar
rolick22 rolick22 is offline
 
Join Date: Oct 2013
Location: Powell, OH
Posts: 115
Default

Sorry, I wish I at least had the builder instructions.
__________________
_____________________________________________
David Rohrlick
PPSEL A&P
RV-12 Finished (Empennage, Fuselage(1st gen), and Wing kit)
Empennage finished (need to add the panel cut out)
Wings finished (need to add the left landing light)
iS Finishing Kit In work
iS Fuselage Finished
1st GEN FUSELAGE SOLD
Serial#12-0864
N864DR Reserved
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 02:03 PM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.