VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics


Go Back   VAF Forums > Model Specific > RV-14
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 11-29-2016, 10:03 PM
KeithB KeithB is offline
 
Join Date: Mar 2014
Location: Granbury, TX
Posts: 110
Default Aileron Hinge Service Bulletin SB 16-03-28

This is a cautionary post for RV-14 builders completing the wing kit and incorporating Service Bulletin 16-03-28 for aileron hinge brackets. It might also apply to the RV-10 as the hinges and SB kit are the same.

When the service bulletin came out for the aileron hinge brackets, I had largely completed the wings, but had not riveted on the bottom skins (to allow for avionics decisions such as auto pilot servo, magnetometer, etc. to be incorporated later). With the bottom skins still open, I felt it was an opportunity to incorporate the revised aileron hinges with limited difficulty (compared to after the wings are closed up), and opted to order and install the retrofit kit.

I drilled out the spar rivets to remove the old hinge, disassembled the hinge to recover the bearing, reassembled the new hinge and riveted it to the spar per the provided instructions. However, when I went to install the aileron back on the wing, the inboard edge of the aileron now contacted the heads of the AN470AD4 rivets used to join the two halves of the new hinge bracket. In retrospect, of course the new hinge is thicker with the addition of a pair of .125 angles. This increased thickness comes out of the distance between the base of the hinge brackets, and out of the clearance between the leading edge of the aileron and the base of the hinge bracket.

I talked to mothership tech support and the fixes proposed were 1) file/bend the aileron skin to clear the rivet heads, 2) swap or substitute washers and/or spacers on the hinge bolts to move the aileron outboard or 3) drill out AN470 rivets in favor of AN426 ones where the heads interfered. After a limited amount of filing, I abandoned 1) as insufficient and unsatisfactory. 2) turned out to be inadequate by itself. So, for 3) I drilled out the two bottom-most AN470AD4 rivets of the 5 joining the hinge bracket halves, then countersunk the angle and replaced with AN426AD4-11 rivets (yes, they are that long). The upper 3 rivets were okay. In addition, on one aileron, I also needed to reposition washers and modify the spacer to better center the aileron between the two hinge brackets. It ends up a tighter fit than before the hinge bracket replacement, but it works.

I would recommend all 5 AN470AD4 rivets be replaced with AN426AD4 rivets when joining the halves of the new inboard aileron hinge brackets. Some adjustment of spacer/washers may still be required.

I apologize for the quality of the photos.





__________________
Keith Brown

RV-14A Builder - kit #136
N314KC - First flight Mar 8, 2017, Phase I compl Apr 3, 2017, >150 hrs
RV-6A sold
Sport Pilot (weight-shift control) - Airborne XT912
Dues paid 11/2017
Reply With Quote
  #2  
Old 12-01-2016, 05:30 AM
ShortSnorter ShortSnorter is offline
 
Join Date: Dec 2013
Location: NOLA
Posts: 137
Default

Thanks for the update, I too opted to implement the SB now (bottom skins off), except I only completed the left side so far and have not finished the ailerons. Those new brackets are definitely stout!!
__________________
Ryan
RV-14 In-Progress
Build Site
Reply With Quote
  #3  
Old 12-01-2016, 01:54 PM
salto salto is offline
 
Join Date: Apr 2015
Location: Wee Waa Australia
Posts: 229
Default

Great observation, I noticed the same issue and thought I would just file my way out of trouble.
The 426-11 will hopefully be described in an amendment to the service bulletin.
Thanks for chasing this up. 👍
__________________
Kit 140241
Tail Feathers done
Fuselage kit completed.
wings almost complete.
Flaps and ailerons done.
Canopy next. Phew!
Reply With Quote
  #4  
Old 12-01-2016, 02:36 PM
MED MED is offline
 
Join Date: Jul 2015
Location: Aiken, SC
Posts: 167
Default

I wonder how this is addressed in the QB wings?
Reply With Quote
  #5  
Old 11-23-2017, 05:41 PM
HHKing HHKing is offline
 
Join Date: Sep 2014
Location: Aiken, SC
Posts: 7
Default QB Wings

Just put the Left Aileron on and I have contact by the skin on the 470 rivet heads. I think I may be able to file the skin to relieve the contact per 1) above. Really don't want to drill out those -11's!

Last edited by HHKing : 11-23-2017 at 05:44 PM.
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 01:15 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.