Home > VansAirForceForums

- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

Go Back   VAF Forums > Model Specific > RV-14
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Thread Tools Search this Thread Display Modes
Old 12-17-2017, 07:15 PM
czechsix's Avatar
czechsix czechsix is offline
Join Date: Mar 2006
Location: Spring Hill, KS
Posts: 278
Default Break edges of skin around aft window?

For those who have fitted the aft window, did you find it necessary to break the edges of the upper skins (F-01474-L and -R) where they meet the plexiglass in order to get a nice fit? Plans don't mention this when building the tailcone, and if needed I'd rather do it before painting the inside of the skins (I paint interior parts prior to riveting).

Mark Navratil
Spring Hill, KS
RV-8A N2D #80583 - built/flew/sold
RV-14A #140017 - wings complete, empacone in progress...
Reply With Quote
Old 12-17-2017, 11:04 PM
Jake14 Jake14 is offline
Join Date: May 2014
Location: Seattle
Posts: 137

I did, but very slightly. Seemed to help, especially along the top. Best to do it before you dimple, but I imagine most folks have already dimpled at that point
RV-14A #140158 flying
Reply With Quote
Old 12-18-2017, 12:12 AM
control control is online now
Join Date: Feb 2006
Location: Stockholm, Sweden
Posts: 402

I did so, needed?
RV-14 kit #140138
working on the finish kit
wings, tail kit and fuselage basically done
Reply With Quote
Old 12-18-2017, 05:41 AM
Tom023 Tom023 is offline
Join Date: Jul 2011
Location: Cypress, TX
Posts: 201

Yes the plans call for it. See p38-03 step 13. I found it difficult to break the extreme forward edges near the roll bar.
RV14A #140083
Wings, empennage and fuselage slow builds completed
Finish and FWF in progress
2017 Donation
Reply With Quote
Old 12-18-2017, 08:54 AM
Bavafa Bavafa is offline
Join Date: Oct 2007
Location: Sacramento, CA
Posts: 2,199

At least during the construction of the tail cone, the instructions says not to dimple and no mention of edge break for this area. I guess I need to double check those pages. Remember, this part does not get riveted but screwed, there will be a thin layer of proseal or other type seal used for water proofing and you want an straight skin so the aft canopy part can easily slid in-out for fitting.
RV7A - IO360M1B - SOLD
Dues paid

Last edited by Bavafa : 12-18-2017 at 08:56 AM.
Reply With Quote
Old 03-10-2018, 05:43 PM
Bernard Hartnell Bernard Hartnell is offline
Join Date: Jul 2013
Location: Grand Junction, CO
Posts: 59
Default Roll edge with special roller tool only!

It was not possible to roll edges top center due to longatudinal bar over luggage compartment. But plexiglass window will seal better with proseal if edges are rolled as possible. Practice on scrap first to be sure you like the result. Change tool if needed.
Reply With Quote
Old 03-10-2018, 06:13 PM
bkervaski's Avatar
bkervaski bkervaski is offline
Join Date: Mar 2017
Location: Birmingham, Alabama
Posts: 588

Mine was already dimpled at that point but I still put a very slight break on the edges. Turned out good but would have been better if I had done it before the dimpling.
#140376 RV-14A QB IO-390 Thunderbolt
Reserved: N196
Progress: All Kits Done
Reply With Quote

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

All times are GMT -6. The time now is 02:41 AM.

The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.