VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 02-22-2018, 01:26 PM
Kevin Handley Kevin Handley is offline
 
Join Date: Feb 2017
Location: Cambridge ,United Kingdom
Posts: 4
Default Rv12 Spar Pin Light

Hello all
Just bought a rv 12 and noticed that the spar pin light was lit and the engine would not start the owner said that he was told that it was probably a faulty sensor and the pins are in place ok just touch the top of the pins and it should deactivate the light which it did.
Any help to sort this out would be appreciated
ThNks in advance
Reply With Quote
  #2  
Old 02-22-2018, 02:00 PM
DaleB's Avatar
DaleB DaleB is online now
 
Join Date: Sep 2012
Location: Omaha, NE (KMLE)
Posts: 1,882
Default

If it's an older one (not sure about the new ones), there is a magnet glued into the top of each latch pin. One of mine came loose, and would occasionally cause that symptom. All I have to do is push down on the tip of the latch pin to re-seat the magnet, and all's well. Next time I'm in there (and remember it) I need to dab a little epoxy or put a drop of superglue on it.

The alignment of the reed switch can also be a little touchy. You can adjust the position of the switch for more reliable operation. One of mine needed about 1/8" of adjustment right after I bought it.
__________________
Dale
Omaha, NE
RV-12 # 222 N980KM "Screamin' Canary" (bought flying)
Fisher Celebrity (under construction)
Previous RV-7 project (sold)
-=VAF=- 2017 dues paid
Reply With Quote
  #3  
Old 02-22-2018, 03:58 PM
AZLeeJay AZLeeJay is offline
 
Join Date: Dec 2013
Location: Phoenix
Posts: 108
Default

You can always push the spar pin light in and the engine will start with it depressed and continue to run with it un-depressed.
Reply With Quote
  #4  
Old 02-23-2018, 06:55 AM
Mich48041 Mich48041 is offline
 
Join Date: Apr 2008
Location: Riley TWP MI
Posts: 2,678
Default

Move the magnetic reed switch closer to the magnet. Or better yet, mount the reed switch parallel to the magnet.
__________________
Joe Gores
RV-12 Flying
Reply With Quote
  #5  
Old 02-23-2018, 08:11 AM
DonFromTX's Avatar
DonFromTX DonFromTX is offline
 
Join Date: Oct 2010
Location: La Feria Texas
Posts: 3,758
Default

I fought mine longer than I should have, finally achieved success by bending the legs on the clamps to allow a better relationship between the switch and the magnets.
__________________
A&P, PP-SEL, Pathological Flier, EAA Technical Counselor
EAA Chapter 595 President,http://www.595.eaachapter.org/index.htm
Retired US Army Officer
Reply With Quote
  #6  
Old 02-23-2018, 12:06 PM
Tony_T's Avatar
Tony_T Tony_T is offline
 
Join Date: Dec 2008
Location: Lacey, WA
Posts: 1,214
Default Spar pin switch upgrade is available

For the OP and other's with the old style switches. The magnetic spar pin switches are a bit hard to adjust, and can be pesky. Van's changed the design to mechanical push switches in 2015 and there is a retrofit kit available

http://www.vansaircraft.com/pdf/Noti...2015-09-15.pdf

I have upgraded using the kit and the mechanical switches work well and are much easier to adjust.
__________________
Tony
RV-12 #202 -- Flying
Reply With Quote
  #7  
Old 02-24-2018, 12:03 AM
Handclutch Handclutch is offline
 
Join Date: Feb 2015
Location: Bendigo, Australia
Posts: 63
Default

I had the same problem and fixed it by taking about I/8 off the tubes to better expose the magnets - works perfectly now.

Jack
Reply With Quote
  #8  
Old 02-24-2018, 02:53 AM
Kevin Handley Kevin Handley is offline
 
Join Date: Feb 2017
Location: Cambridge ,United Kingdom
Posts: 4
Default Spar pins

Thanks All for your replies
Reply With Quote
  #9  
Old 02-24-2018, 10:23 PM
RFSchaller RFSchaller is offline
 
Join Date: Oct 2010
Location: Phoenix, AZ
Posts: 2,302
Default

I helped a guy fix his. It was actually a bad reed switch, so I recommend putting a strong magnet up against the switch first to be sure its not magnet position that is causing the issue.
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 03:16 PM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.