Home > VansAirForceForums

- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

Old 02-11-2018, 09:25 PM
SteFree RV-8 SteFree RV-8 is offline
Join Date: Jan 2018
Location: Phoenix
Posts: 6
Default Skinning the Horizontal Stabilizer

Hello Group...

I have been working on the Horizontal Stabilizer and I am at the point where it is time to skin it. I have the pre-punched kit and it seem like a jig is not necessary but I wanted to reach out to you guys to see if you can offer advice for the best way to do this. If I need to build a jig I will but I can't find anything in the plans for this and in looking on the internet I can't find anything there. I have the GeoBeck videos but the techniques he discusses seem outdated to the modern kits.

Can anyone offer advice or best practices? I have read the manual and I know I can proceed but I am sure those of you who have, "been there and done that" can offer tricks.

Does anyone have any pictures from their builds they can share?

Any help or guidance is greatly appreciated.

Thanks in advance

Steve (reserving N902SE) Freeman
Steve Freeman
Built and Flying Zenith CH650, N902AL
Now Building RV-8

"If you choose not to decide you still have made a choice."

Neal Peart
Reply With Quote
Old 02-11-2018, 09:35 PM
Robin8er Robin8er is offline
Join Date: Sep 2015
Location: Oahu HI
Posts: 189

No jig is necessary, all the holes should line right up. Just make sure you plane your riveting order, you dont want to rivet in such a way that you cannot reach some of the rivets.
N695RA Reserved
Emp and Wings done, working on Fuselage.

Born to fly, forced to work
Reply With Quote
Old 02-12-2018, 05:44 AM
Mark Dickens's Avatar
Mark Dickens Mark Dickens is offline
Join Date: Apr 2012
Location: Collierville, TN (KFYE)
Posts: 851

With the -2 matched hole kit, a jig is not necessary, but make sure you've got clecos in at least every other hole. While you don't need a jig per se, plan out how you're going to hold the stab still and vertical while you work. A little attention paid to setting up the riveting session will pay big dividends in wear and tear on both you and the HS.
RV-8 #81077 Super Slow Build
Titan IOX-370, Dual P-Mags, AFP FM200A FI, Sensenich GA Prop
First Flight November 20, 2016 - Phase One Complete June 1, 2017
Reply With Quote
Old 02-12-2018, 08:16 AM
wirejock's Avatar
wirejock wirejock is online now
Join Date: Oct 2005
Location: Estes Park, CO
Posts: 2,823
Default HS riveting

I think the 7 & 8 HS are the same if not very similar. Follow the manual sequence.
I did build a jig for the elevators and ailerons but it was not required. If you have enough Clekos, plug every hole.
Larry Larson
Estes Park, CO
wirejock at yahoo dot com
Donated 12/01/2017. Plus a little extra.
RV-7A #73391, N511RV reserved (1,800+ hours)
HS SB, empennage, tanks, wings, fuse, working finishing kit
I cannot be, nor will I be, held responsible if you try to do the same things I do and it does not work and/or causes you loss, injury, or even death in the process.

Last edited by wirejock : 02-13-2018 at 08:42 AM.
Reply With Quote
Old 02-12-2018, 10:31 PM
longranger's Avatar
longranger longranger is offline
Join Date: Mar 2007
Location: 45G, Brighton, MI
Posts: 1,746

Just figure out some way to hold it still while riveting. Itís nearly impossible to do a good job of riveting if youíre chasing your work across the bench. Here is the first of four entries in my build log on how I riveted the HS for my -7.
Miles (VAF# 1238, Paid up as of 12/2016)
RV-7 TU 904KM (reserved)
Wings Structurally Complete!!
SB Fuselage Just Past QB Stage

Construction Log
Picasa: Empennage Album, Wings Album, Fuselage Album

1955 Cessna 170B flying since 1982

'To get something you never had, you have to do something you never did.' -Unk.
Reply With Quote

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

All times are GMT -6. The time now is 05:17 PM.

The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.