VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 03-20-2016, 05:13 PM
Douglas Douglas is offline
 
Join Date: Mar 2016
Location: Roland, Arkansas
Posts: 5
Default Fuel Sender Floats

I am about to close the access panel and install the fuel sender unit, but I am not sure if the fuel sender and float are supposed to rotate. I have bent and cut the metal rod that attaches the float to the sender unit correctly and attached it. I noticed will test fitting that the float and metal rod will swing around easily. Is it supposed to do that? Is there not a chance of it hanging up in a barrel roll or unusual attitude?
Reply With Quote
  #2  
Old 03-20-2016, 05:56 PM
stamper stamper is offline
 
Join Date: Dec 2012
Location: alaska
Posts: 309
Default sender

Doug , I believe that they will swing around if you do not snap the rod into the plastic piece. Once you do they should be locked into the position that you snapped or locked them into that plastic thing-a-majig.
I could be wrong but I had to replace mine a moth ago and noticed this same thing.
__________________
2016 dues paid
RV10 Started Jan 2013
DAR sign off April 23rd 2016


PA-18
PA-46
Cessna 172 and T182RG
RV-10
Reply With Quote
  #3  
Old 03-20-2016, 06:08 PM
Carl Froehlich's Avatar
Carl Froehlich Carl Froehlich is offline
 
Join Date: Dec 2007
Location: Dogwood Airpark (VA42)
Posts: 1,062
Default

Doug,

I saw this once while looking at an RV-8 project. The builder misinterpreted how to bend the rod and did not put the 90 degree bend at the end that goes through the plastic holder. He only had the rod in the plastic clips. The end that goes through the plastic is what prevents rotation.

Carl
Reply With Quote
  #4  
Old 03-20-2016, 06:17 PM
Douglas Douglas is offline
 
Join Date: Mar 2016
Location: Roland, Arkansas
Posts: 5
Default

Thanks, I will take a closer look at the plans.
Reply With Quote
  #5  
Old 03-20-2016, 06:31 PM
Douglas Douglas is offline
 
Join Date: Mar 2016
Location: Roland, Arkansas
Posts: 5
Exclamation

Got it! I read the instruction sheet a couple of times and looked over the Van plans. Found my problem. The Van plans call for 3 inches, 90 degree bend and then 3 inches, but no mention of the small bend on the end. When I was reading the instructions supplied with the sender unit, when they mentioned a 90 degree bend, I thought they were referring to same bend as Vans. Plus the diagram that came with the sending unit is difficult to follow. But, now making it fit based on what you have told me it makes sense. Too bad I have cut the rods 3 inch X 3 inch, I don't have enough length to make the small bend on the end. I know who I am calling tomorrow morning. "I would like to order two rods please." Thanks again for the input, hope this helps others in the future, hopefully before they bend and cut.
Reply With Quote
  #6  
Old 09-22-2017, 11:35 PM
precession precession is offline
 
Join Date: Apr 2006
Posts: 111
Default

Glad you posted this. This helped me avoid making the same mistake when installing a new sender.
__________________
RV-4 in NJ
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 08:29 PM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.