VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 12-05-2017, 04:58 PM
coffeeguy coffeeguy is offline
 
Join Date: Jul 2015
Location: Lake in the Hills, IL
Posts: 86
Default What was that countersink set to?

I had to reach for the countersink cage today and couldn't remember if it was set for rivet depth or minus 7 clicks. Argh, I hate to drill a few new holes in angle stock, deburr and test it out. I came up with the idea of using red and green electrical tape wrapped around the cs cage. Green for skin, red for watch out, it's deeper and set to -7 clicks. I realized I didn't have any colored electrical tape, so I went to the junk drawer and grabbed some bread twist ties.

If it doesn't have a twist tie on it, check it. I also had the idea of taking some thicker flat stock (don't have any on hand, though) and making something like a pegboard. One for #30 and one for #40. Drill all of the holes once, then just check your cs depth on one or two holes as you need them.

__________________
Jeff Dingbaum
RV-14A empennage, wings
Cherokee 180
2017 dues paid
Reply With Quote
  #2  
Old 12-05-2017, 05:07 PM
wirejock's Avatar
wirejock wirejock is offline
 
Join Date: Oct 2005
Location: Estes Park, CO
Posts: 2,726
Default Tip

Good tip but I never trust any of my cages. I take scrap and drill tons of #40 and #30 holes. Before any use, I test the cage. I know they should stay set but those pesky gremlins love to mess with my tools.
__________________
Larry Larson
Estes Park, CO
http://wirejockrv7a.blogspot.com
wirejock at yahoo dot com
Donated 12/01/2017. Plus a little extra.
RV-7A #73391, N511RV reserved (1,800+ hours)
HS SB, empennage, tanks, wings, fuse, working finishing kit
Disclaimer
I cannot be, nor will I be, held responsible if you try to do the same things I do and it does not work and/or causes you loss, injury, or even death in the process.
Reply With Quote
  #3  
Old 12-05-2017, 05:37 PM
Bruce's Avatar
Bruce Bruce is offline
 
Join Date: Feb 2006
Location: ADDISON,TX
Posts: 1,014
Default

+1 on Larrys advice.

Been there.
__________________
Bruce (BOOMER) Pauley
Kathy (KAT) Pauley

RV 7A--"MISS MARIE"--- N177WD (SOLD FLYING)72742
VAF #582-----------------EAA LIFETIME MEMBER
EX -KC-135A -------------BOOM OPERATOR #3633
VAN'S FLIGHT------------#6930

See you in OSHKOSH


http://www.mykitlog.com/users/index....ley&project=84


2006-2017 DUES PAID
Reply With Quote
  #4  
Old 12-05-2017, 08:17 PM
scsmith scsmith is offline
 
Join Date: Jan 2008
Location: Ashland, OR
Posts: 1,705
Default

What is the purpose of the -7 click setting?
__________________
Steve Smith
Aeronautical Engineer
RV-8 N825RV
IO-360 A1A
WW 200RV
"The Magic Carpet"
Hobbs 470 in 8 years
also LS-6-15/18 sailplane
Reply With Quote
  #5  
Old 12-05-2017, 09:15 PM
Bill Boyd's Avatar
Bill Boyd Bill Boyd is offline
 
Join Date: Sep 2006
Location: Landing field "12VA"
Posts: 952
Default

I've used 2 different cages over the years and learned with both that the depth of cut is dependent on applied pressure to such a degree that I always "sneak up" on the desired CSK depth by means of multiple passes. It seems to be an inherent weakness of the tool.

I've also earned to give myself grace over the occasional too-deep hole and just live with it. The rivets seem to drive good and tight even when the head is slightly below the surface of the piece. A proud manufactured head is to be avoided far more than one that's just a tad too deep.

That said, it is a horrible feeling to forget to check the setting and hog a hole out way beyond spec. Not sure how I know this, but I've been told
__________________
Bill Boyd

Hop-Along Aerodrome (12VA)
RV-6A - N30YD - flying since '98
RV-10 - N130YD reserved - under construction

donating monthly to the VAF - thanks, Doug
Reply With Quote
  #6  
Old 12-05-2017, 09:39 PM
coffeeguy coffeeguy is offline
 
Join Date: Jul 2015
Location: Lake in the Hills, IL
Posts: 86
Default -7 clicks

Quote:
Originally Posted by scsmith View Post
What is the purpose of the -7 click setting?
Most of the time it is because you will have a dimpled skin at that location, but it could be for any two pieces that are joined with a flush rivet. It needs to be deeper for the dimpled skin to sit in the countersink.

From the construction manual:
Use the appropriate rivet or screw as a gauge when you machine countersink. Stop when the rivet or screw is flush. For a dimpled
skin riveted onto a machine countersunk surface the countersink must be slightly deeper as mentioned earlier. Proper depth is .007
deeper than when the rivet head is flush. This depth correction corresponds to seven "clicks" on a microstop countersink tool
indexed in .001 inch increments.
__________________
Jeff Dingbaum
RV-14A empennage, wings
Cherokee 180
2017 dues paid
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 04:48 PM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.