VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #141  
Old 07-30-2017, 10:00 PM
rv6ejguy's Avatar
rv6ejguy rv6ejguy is offline
 
Join Date: Mar 2005
Location: Calgary, Canada
Posts: 3,880
Default

Some more info from Dave flying back home from Osh:

"This was after leaving Great Falls Montana on the way home. Those are obviously incorrect winds and xw. Then look at 31.4 mpg at this low altitude at about 20” MAP at 2200 rpm, while truing 197mph. I love this system, you can full power or lean with no problems and it starts like a car, even on hot starts."





Dave says he's overcooling in cruise running LOP and will look at reducing the inlet ring size at some point.

The SDS programmer here shows the AFR at 16.7 which is well LOP.
__________________

Ross Farnham, Calgary, Alberta
Turbo Subaru EJ22, Marcotte M-300, IVO, RV6A C-GVZX flying from CYBW- 415.8 hrs. on the Hobbs,
RV10 95% built- Sold 2016
http://www.sdsefi.com/aircraft.html
http://sdsefi.com/cpi.htm



Last edited by rv6ejguy : 07-31-2017 at 08:16 AM.
Reply With Quote
  #142  
Old 08-01-2017, 04:36 PM
rv6ejguy's Avatar
rv6ejguy rv6ejguy is offline
 
Join Date: Mar 2005
Location: Calgary, Canada
Posts: 3,880
Default SDS Digital Fuel Flow Accuracy

Some more feedback from Dave today showing the accuracy of our optional FF software. We generate a pulse train from the ECU to feed the engine monitor so no Red Cubes are required.

"Just wanted to let you know that the speed we did in the race was while burning 14.5 gph, confirmed by the max FF indication I was getting when using the SDS fuel signal was within 0.1gph and confirmed by the fuel added at the pump at the pit stop, so at that flow, the FF was accurate to within .227 gals of all the 32 gals in my tanks. During those conditions my engine was producing about 194 real hp at 2830 rpm. Also during the race I burned the left tank out until I saw the fuel pressure fluctuate 2-3 lbs off of max pressure then changed the selector to the tanks without even a hesitation in the engine operation.

hp = 14.5 gph x 5.9 lbs/gal / 0.44 bsfc"
__________________

Ross Farnham, Calgary, Alberta
Turbo Subaru EJ22, Marcotte M-300, IVO, RV6A C-GVZX flying from CYBW- 415.8 hrs. on the Hobbs,
RV10 95% built- Sold 2016
http://www.sdsefi.com/aircraft.html
http://sdsefi.com/cpi.htm


Reply With Quote
  #143  
Old 08-01-2017, 04:54 PM
M McGraw's Avatar
M McGraw M McGraw is offline
 
Join Date: Dec 2012
Location: Greenback, TN
Posts: 309
Default FF calc

I have been collecting a lot of data on my install. I do plan to publish it in the future after about 100 hours of use. Currently - at 50 hours - I am consistently within 0.1 gallons at fill up on my IO-390 using the SDSEFI system.
__________________
Marvin McGraw, 5TN4
RV-14. #140039 Complete
Flight hours: 50+
Reply With Quote
  #144  
Old 08-01-2017, 05:11 PM
rv6ejguy's Avatar
rv6ejguy rv6ejguy is offline
 
Join Date: Mar 2005
Location: Calgary, Canada
Posts: 3,880
Default

Thanks Marvin. Barry will be happy to know all his hard work paid off writing this software. It was dead on in lab testing but nothing like these real world results on running engines to fully confirm.
__________________

Ross Farnham, Calgary, Alberta
Turbo Subaru EJ22, Marcotte M-300, IVO, RV6A C-GVZX flying from CYBW- 415.8 hrs. on the Hobbs,
RV10 95% built- Sold 2016
http://www.sdsefi.com/aircraft.html
http://sdsefi.com/cpi.htm


Reply With Quote
  #145  
Old 08-01-2017, 07:01 PM
Toobuilder's Avatar
Toobuilder Toobuilder is offline
 
Join Date: Jul 2009
Location: Mojave
Posts: 3,609
Default

Im very happy to hear the computed fuel flow of the SDS ECU is consistently accurate. I never liked that fuel flow meter clap trap on the engine and especially after Dan dissected one which revealed the miniscule flow passages. Good riddance!

I have just flow tested my new fuel system for the Rocket and am happy to report that it flows 60 GPH with the single pump and 90 with the second running. During the retrofit I went to great lengths to eliminate 90 degree fittings on the suction side, including changing the in tank pickup to a straight fitting. An interesting side note is that I also intended to run two Faccet cube pumps as "pushers" right at the wing roots thinking that my planned use of auto gas would need help to prevent vapor lock. I decided to only install one cube pump for the test period so that I could easily determine if I needed to add the second, or remove the first. During the FF test I noted that the "cube side" sounded more labored than the "non cube side" despite the fact that there was no measurable difference in delivered flow rate. Based upon this, I would not be surprised to find that the added restriction of the cube pump has actually increased my susceptibility to vapor related issues. Testing will determine.

At any rate, the less hardware in the loop, the better! Thanks Ross!
__________________
WARNING! Incorrect design and/or fabrication of aircraft and/or components may result in injury or death. Information presented in this post is based on my own experience - Reader has sole responsibility for determining accuracy or suitability for use.

Michael Robinson
______________
Harmon Rocket II -SDS EFI instalation in work
RV-8 - Flying
1940 Taylorcraft BL-65 -flying
PA-20-inspired "family truckster" -in work
Reply With Quote
  #146  
Old 08-01-2017, 07:41 PM
rv6ejguy's Avatar
rv6ejguy rv6ejguy is offline
 
Join Date: Mar 2005
Location: Calgary, Canada
Posts: 3,880
Default

Very good numbers Brad. What timing are you running? Compression ratio? Airframe? Prop?
__________________

Ross Farnham, Calgary, Alberta
Turbo Subaru EJ22, Marcotte M-300, IVO, RV6A C-GVZX flying from CYBW- 415.8 hrs. on the Hobbs,
RV10 95% built- Sold 2016
http://www.sdsefi.com/aircraft.html
http://sdsefi.com/cpi.htm


Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 07:17 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.