VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics


Go Back   VAF Forums > Model Specific > RV-12
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 03-03-2018, 06:54 PM
Brett H Brett H is offline
 
Join Date: Oct 2013
Location: Columbus, Indiana
Posts: 27
Default Canopy Struts Are Rubbing the Canopy Frame

I am currently in the process of trying to get my canopy frame to fit.

In doing so, I have noticed that the inside edge of the canopy struts rub the canopy frame when the canopy frame is closed. The paint on the inside edge of the struts has been worn off. Also, it is not possible to get a piece of paper to slide between the strut and the canopy frame when closed. Further, the alignment between the canopy frame and the fuselage differs if the struts are or are not installed.

Anyone seen this before? If so, what did you do about it?

Thanks.

Brett Herrick
Columbus, IN
Reply With Quote
  #2  
Old 03-04-2018, 04:13 AM
mike newall's Avatar
mike newall mike newall is offline
 
Join Date: Jan 2005
Location: Yorkshire, England
Posts: 1,636
Default

You have shim/washer options in the print to help in this area. Go back a page and look.

I take it you have the struts on the right way round...
__________________
"I add a little excitement, a little spice to your lives, and all you do is complain!" - Q

Donated in 2018
Reply With Quote
  #3  
Old 03-04-2018, 10:13 AM
Brett H Brett H is offline
 
Join Date: Oct 2013
Location: Columbus, Indiana
Posts: 27
Default

Mike:

First, thanks for your response.

Yes, the "rod end" of the strut is attached to the fuselage and other end is attached to the canopy.

Regarding the shim washer described in step 3 of sheet 34-03, isn't that to provide clearance between the forward arms of the canopy frame and the upper fuselage skin? Yes, I had to add a thin washer on each side.

I am installing the new struts with the metal ends. One thing that I am not positive of is which version of the C-1204 bushing is to be used. I believe that steel ended struts use the version of the C-1204 that has a tapered transition between the two outside diameters rather than no transition. But, I have the same issue with both bushings.

Any other thoughts would be appreciated.

Brett H
Columbus, IN
Reply With Quote
  #4  
Old 03-04-2018, 11:20 AM
mike newall's Avatar
mike newall mike newall is offline
 
Join Date: Jan 2005
Location: Yorkshire, England
Posts: 1,636
Default

On the front mount where the bronze bush sits, we had to pack out with washers about 2 or 3 to get everything to clear - both skin and strut. Can't get a snap as everything is tucked into the glass fairing now.

You need a snap from someone else who is just fitting the canopy.
__________________
"I add a little excitement, a little spice to your lives, and all you do is complain!" - Q

Donated in 2018
Reply With Quote
  #5  
Old 03-04-2018, 06:32 PM
Brett H Brett H is offline
 
Join Date: Oct 2013
Location: Columbus, Indiana
Posts: 27
Default

Mike:

On each side of the canopy frame I put two standard thickness washers between the canopy frame bushing and the fuselage, this didn't reduce the contact between the strut and the bottom of the canopy frame arm. So, I removed them.

Next I put a standard thickness washer between the C-1204 bushing and the canopy frame arm on each side. This reduced the interference. But, didn't resolve it and means that that AN509 screw will need to longer (i.e. stick out more).

I'm starting to think that the interference / rubbing is going to happen and that the best solution is to round the bottom edge of the canopy frame arm so that the strut has smooth surface to ride up on. Or there is something wrong with the parts that I have.

Brett H
Columbus, IN
Reply With Quote
  #6  
Old 03-13-2018, 07:21 PM
DaveWelch DaveWelch is offline
 
Join Date: Mar 2005
Location: Huntsville, AL
Posts: 316
Default Don't cut any metal yet

Quote:
Originally Posted by Brett H View Post
Mike:

On each side of the canopy frame I put two standard thickness washers between the canopy frame bushing and the fuselage, this didn't reduce the contact between the strut and the bottom of the canopy frame arm. So, I removed them.

Next I put a standard thickness washer between the C-1204 bushing and the canopy frame arm on each side. This reduced the interference. But, didn't resolve it and means that that AN509 screw will need to longer (i.e. stick out more).

I'm starting to think that the interference / rubbing is going to happen and that the best solution is to round the bottom edge of the canopy frame arm so that the strut has smooth surface to ride up on. Or there is something wrong with the parts that I have.



Brett H
Columbus, IN
I wouldn't cut or shave any metal yet until you're certain all else is according to plan. I don't recall the interference you describe being often discussed.
Can you post a picture of your strut attachments (top and bottom) and where "the rub" is?

Dave
__________________
Dave
RV12 N951DZ
First Flight 9/23/16!
No paint yet. Working on a scheme with John Deere colors or accents.
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 03:34 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.