VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 09-10-2019, 05:31 PM
az_gila's Avatar
az_gila az_gila is online now
 
Join Date: Jan 2005
Location: 57AZ - NW Tucson area
Posts: 9,937
Question Autopilot Q.

Can anyone share pictures for their connector hookup for the RV-10 Dynon Roll Servo?

I'm using a D-sub connector but can make changes if needed.
__________________
Gil Alexander
EAA Technical Counselor, Airframe Mechanic
Half completed RV-10 QB purchased
RV-6A N61GX - finally flying
Grumman Tiger N12GA - flying
La Cholla Airpark (57AZ) Tucson AZ
Reply With Quote
  #2  
Old 09-10-2019, 11:04 PM
paul330 paul330 is offline
 
Join Date: Feb 2007
Location: Mpumalanga, South Africa
Posts: 1,063
Default

You need an extra connection for the power as the lines in the standard D-Sub connection aren't sufficient to run the servo. I used a simple spade connector and local earth.
__________________
Paul
Mercy Air, White River FAWV
RV-10 ZU-IIZ - "Zeus"
Building Bearhawk Bravo - RV-18 not available
2019 Donation Made
Reply With Quote
  #3  
Old 09-11-2019, 12:56 AM
awmuhs's Avatar
awmuhs awmuhs is offline
 
Join Date: Jun 2013
Location: Tucson, Az
Posts: 139
Default autopilot servo

Since you donít use all of the pins because there are fewer than 9 wires I used 2 open pins for power. It made the connection at the servo nice and clean.
__________________
Alan Muhs
Tucson, Arizona
Dues overpaid December 17, 2018
RV12iS Southern Arizona Teen Aviation: #1 airplane flying, #2 airplane working on finish kit, #3 airplane working on tail kit.
RV10 flying since July 2014- 650hrs as of Dec 2019
RV6A sold after 500 hours of flying
Reply With Quote
  #4  
Old 09-11-2019, 01:04 AM
az_gila's Avatar
az_gila az_gila is online now
 
Join Date: Jan 2005
Location: 57AZ - NW Tucson area
Posts: 9,937
Default

I've got that covered since I make the Alexander Network Hub...

What I'm looking for is how the connectors are hooked up.
__________________
Gil Alexander
EAA Technical Counselor, Airframe Mechanic
Half completed RV-10 QB purchased
RV-6A N61GX - finally flying
Grumman Tiger N12GA - flying
La Cholla Airpark (57AZ) Tucson AZ
Reply With Quote
  #5  
Old 09-12-2019, 10:43 PM
az_gila's Avatar
az_gila az_gila is online now
 
Join Date: Jan 2005
Location: 57AZ - NW Tucson area
Posts: 9,937
Smile

No-one has any pictures of how they hooked up a Dynon Roll Servo?
__________________
Gil Alexander
EAA Technical Counselor, Airframe Mechanic
Half completed RV-10 QB purchased
RV-6A N61GX - finally flying
Grumman Tiger N12GA - flying
La Cholla Airpark (57AZ) Tucson AZ
Reply With Quote
  #6  
Old 09-12-2019, 11:00 PM
Jake14 Jake14 is offline
 
Join Date: May 2014
Location: Seattle
Posts: 257
Default

here's a 14, should be similar to a 10

https://imgur.com/a/jwfkVdg

if you're looking for pin nos or other details, try this


https://www.dynonavionics.com/includ...ions_Rev_H.pdf
__________________
RV-14A #140158 flying

Last edited by Jake14 : 09-12-2019 at 11:07 PM.
Reply With Quote
  #7  
Old 09-13-2019, 09:50 AM
Lynnb's Avatar
Lynnb Lynnb is offline
 
Join Date: Jan 2014
Location: Cedar Hill, TX
Posts: 305
Default

Not sure what pictures you'd like. I used a 9 pin d-sub:




Let me know if the two pictures above don't show up, or if you want some more.

Lynn
__________________
RV-10 in Process
Reply With Quote
  #8  
Old 09-14-2019, 09:43 AM
jwilbur jwilbur is online now
 
Join Date: Dec 2010
Location: Culpeper, VA
Posts: 662
Default pics

I have some pics:

Here:
https://520lw.wordpress.com/2013/04/...on-complete-2/

and here:
https://520lw.wordpress.com/2013/04/...ring-plumbing/
__________________
-Joe Wilbur (N520LW)
Phase II - 11/2017
First flight - 8/2017
RV-10 Build Log
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 06:53 PM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.