VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 12-30-2017, 02:50 PM
9GT's Avatar
9GT 9GT is offline
 
Join Date: Jan 2010
Location: Southern Michigan
Posts: 1,410
Default Tip: DIY Penetration Kit For Under $10!

I couldn't bear the thought of spending $57 for a 3/4" firewall penetration kit so I did some digging around on the internet. I found these on Amazon in a variety of sizes and quantities. Two for $7.85, and free shipping with my Prime membership: https://www.amazon.com/uxcell-Diamet...ld+Neck+Flange . 2" X 1/2" stainless steel washers from my favorite hardware store at .45 cents each. They work as a backer on the cabin side of the firewall. Just drill out the 1/2" hole to 3/4" with a good Unibit and deburr, then match drill the mounting holes, or drill new ones to suit. I had a foot of 1" I.D. silicone fire-sleeve leftover from another project and have a tube of 3M 200 Fire Stop sealant to seal up the firewall on hand. Add a couple SS worm clamps and your good to go. The flanges have a drilled hole in side of the tube for a set screw but the sealant, worm clamp, and overlaying fire sleeve will take care of that. I have a TIG so will probably weld the holes closed though I do not thing it is necessary. So here I have 2 nice stainless steel firewall penetration kits for about $5.00 each.
[IMG]DSC01987 by David C, on Flickr[/IMG]
[IMG]DSC01988 by David C, on Flickr[/IMG]
__________________
David C.
Howell, MI

RV-9A: Under Construction. N161RV (Reserved)
RV-10: N959RV Completed 12/29/2013 SOLD 08/23/2016

"Donor Exempt" but donated through Dec. 2018

Last edited by 9GT : 12-30-2017 at 02:56 PM.
Reply With Quote
  #2  
Old 12-30-2017, 03:19 PM
Mike S's Avatar
Mike S Mike S is offline
Senior Curmudgeon
 
Join Date: Sep 2005
Location: Dayton Airpark, NV A34
Posts: 14,006
Default

Ah........the joy of experimental aviation
__________________
Mike Starkey
VAF 909

Rv-10, N210LM.

Flying as of 12/4/2010

Phase 1 done, 2/4/2011

Sold after 240+ wonderful hours of flight.

"Flying the airplane is more important than radioing your plight to a person on the ground incapable of understanding or doing anything about it."
Reply With Quote
  #3  
Old 12-30-2017, 05:49 PM
wirejock's Avatar
wirejock wirejock is online now
 
Join Date: Oct 2005
Location: Estes Park, CO
Posts: 2,881
Default Firewall pass thru

Excellent. Not too far away so I'm ordering a few. Thanks for the tip.
__________________
Larry Larson
Estes Park, CO
http://wirejockrv7a.blogspot.com
wirejock at yahoo dot com
Donated 12/01/2017. Plus a little extra.
RV-7A #73391, N511RV reserved (1,800+ hours)
HS SB, empennage, tanks, wings, fuse, working finishing kit
Disclaimer
I cannot be, nor will I be, held responsible if you try to do the same things I do and it does not work and/or causes you loss, injury, or even death in the process.
Reply With Quote
  #4  
Old 12-30-2017, 08:17 PM
160kt 160kt is offline
 
Join Date: Feb 2005
Posts: 74
Default Stainless steel Flange

I’m curious what alloy of Stainless these flanges are made from? Could you put a magnet on one and see if it sticks at all? I like to keep magnetics to a minimum in front of the compass.
Thanks

Last edited by 160kt : 02-21-2018 at 05:58 PM.
Reply With Quote
  #5  
Old 12-31-2017, 12:37 AM
rv8ch rv8ch is offline
 
Join Date: Feb 2005
Location: LSGG
Posts: 2,250
Default Great idea!

I used this method with my first engine, and it was very good. For a flange and tube, I used stainless steel bathroom safety grab bars.

http://www.aeroelectric.com/articles.../firewall.html

For the second engine, I purchased the well-known kits, since I needed much smaller penetrations.

http://www.aircraftspruce.com/catalo...ration_kit.php

I've seen many methods on RVs and certified aircraft that I wouldn't feel comfortable with, like just a hole with a dab of RTV to "protect" the wires, plastic snap bushing with RTV, rubber grommet with nothing else, and even the rubber grommet with the stainless steel cover, but these aircraft seem to have been signed off and fly. \_(ツ)_/
__________________
Mickey Coggins
http://rv8.ch
Reply With Quote
  #6  
Old 12-31-2017, 08:26 AM
Electrogunner Electrogunner is online now
 
Join Date: Aug 2016
Location: Quarryville ,pa
Posts: 244
Default FWF

I literallly just installed my stainless steel shower rod holders last week. Glad to see Im not the only thrifty one in the bunch. I just could not spend $60/ea on them. I did cut mine down to the set screw though.
__________________
Donation Made For 2017
RV10 N620RV
IO540 C4B5
Whirlwind 375RV
Garmin G900X
Finishing and FWF is ongoing
Reply With Quote
  #7  
Old 12-31-2017, 05:51 PM
hgerhardt's Avatar
hgerhardt hgerhardt is offline
 
Join Date: Oct 2006
Location: torrance, ca
Posts: 416
Default

Another nice way is to take a steel AN bulkhead fitting and bore out the hole on a lathe. You can also turn down the OD and remove the threads everywhere except where the nut needs to go to lighten it.
Reply With Quote
  #8  
Old 01-01-2018, 11:23 AM
Ethanol1 Ethanol1 is offline
 
Join Date: Oct 2007
Location: MN
Posts: 34
Default No longer available

You must of bought the last ones.

https://www.amazon.com/uxcell-Diamet...ld+Neck+Flange
__________________
Mike York
President EAA Ch 25
Reply With Quote
  #9  
Old 01-01-2018, 11:49 AM
kentlik's Avatar
kentlik kentlik is offline
 
Join Date: Sep 2015
Location: Oregon
Posts: 407
Default

Quote:
Originally Posted by Ethanol1 View Post
https://www.amazon.com/gp/product/B0...8BJ6JWOC&psc=1

Here are similar items.
__________________
Kentlik
RV-7A in progress
http://www.imdb.com/name/nm0527486/?
Private pilot, ASEL!
EAA 105 Chapter 7S3
financial contributor

"The credit belongs to the man who is actually in the arena..." Teddy Roosevelt
Reply With Quote
  #10  
Old 01-01-2018, 11:56 AM
Av8torTom's Avatar
Av8torTom Av8torTom is offline
 
Join Date: Nov 2009
Location: Yardley, PA
Posts: 1,140
Default Great idea!

They remind me of SS marine rail fittings. These might be on the heavy side, but offer a choice of angles.

http://www.go2marine.com/product/675...ss-steel.html?

__________________
RV-9A (empennage completed, both wings completed, ready to hang engine)
N677AT reserved
Superior XP O-320, 160HP
Picture log: http://s271.photobucket.com/albums/j...8tor215/RV-9A/
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 09:04 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.