VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 04-17-2018, 09:35 PM
RepmikeBrown RepmikeBrown is offline
 
Join Date: Oct 2012
Location: Tahlequah , Ok
Posts: 129
Default Culprit

Big milestone today. I finished installing wings, plumbing, wiring and checked all of my aileron up and down movements. The stick movement seemed a little heavy left and right but ok forward and aft. I probably wouldnít have ever second guessed the heaviness had there not been another RV4 in the hanger next to me. Itís movements were effortless, but I did have the servos connected from an auto pilot installed. I thought maybe this added the extra drag in the controls. Not satisfied I disconnected the aileron servo and still had the heavy stick both left and right. I start with left and right aileron bushings/washers, any possible rubbing of close parts. Moved on to the aileron push rods checking all rod end bearings and washers. Next the bell crank and then the large push rod tubes all moving freely I install them back and still heavy left /right movement on stick. I examine the stick control for binding or interference, and then finally removed the heim bearings for inspection. Iím down 2 days so far, but finally found the culprit. The rear heim bearing has been damaged ever so slightly. The small crease on the brass
has also creased the interior of the housing race causing the bearing to bind. I just wished Iíd started looking from that point first. Lesson learned.
__________________
RV4 UnderConst
repmikebrown@yahoo.com
Mike Brown
Reply With Quote
  #2  
Old 04-18-2018, 05:25 AM
Michael Henning Michael Henning is offline
 
Join Date: Jun 2011
Location: Nashua, NH
Posts: 473
Default

Itís always the last thing you check🤔
__________________
Mike
RV-4 #2750
N654ML
IO-360
WW150C Prop
1018 lbs
Flying
Reply With Quote
  #3  
Old 04-18-2018, 05:43 AM
snopercod's Avatar
snopercod snopercod is offline
 
Join Date: Aug 2016
Location: Asheville, NC
Posts: 1,106
Default

We pay $60 for those rod ends because of the excellent quality control /sarc
__________________
(2018 dues paid)
Reply With Quote
  #4  
Old 04-18-2018, 06:58 AM
Sam Buchanan's Avatar
Sam Buchanan Sam Buchanan is offline
hall monitor
 
Join Date: Dec 2004
Location: North Alabama
Posts: 3,701
Default

That type of damage is often caused by careless use of a wrench to tighten the bearing. Good catch!
__________________
Sam Buchanan
1999 RV-6
1918 Fokker D.VII replica

Last edited by Sam Buchanan : 04-18-2018 at 07:26 AM.
Reply With Quote
  #5  
Old 04-18-2018, 07:17 AM
DanH's Avatar
DanH DanH is offline
 
Join Date: Oct 2005
Location: 08A
Posts: 7,549
Default

Whatever the cause, kudos to Mike for chasing it down, and not blowing off the control drag, as we see so many do.
__________________
Dan Horton
RV-8 SS
Barrett IO-390
Reply With Quote
  #6  
Old 04-18-2018, 07:52 AM
AlexPeterson's Avatar
AlexPeterson AlexPeterson is offline
 
Join Date: Sep 2005
Location: Maple Grove, MN
Posts: 2,043
Default

Mike, nice catch. Could that damage have been from the two rod ends on that particular pushrod being clocked with a "twist", causing binding? It almost looks like a washer was grinding into the brass.
__________________
Alex Peterson
RV6A N66AP 1600+ hours
Maple Grove, MN
Reply With Quote
  #7  
Old 04-18-2018, 08:18 AM
RepmikeBrown RepmikeBrown is offline
 
Join Date: Oct 2012
Location: Tahlequah , Ok
Posts: 129
Default Twist

The only thing I can think is yes, plus over torquing which caused the damage
__________________
RV4 UnderConst
repmikebrown@yahoo.com
Mike Brown
Reply With Quote
  #8  
Old 04-19-2018, 08:23 AM
EXflyer EXflyer is offline
 
Join Date: Jan 2016
Location: Chiloquin OR
Posts: 59
Default

Quote:
Originally Posted by RepmikeBrown View Post
The only thing I can think is yes, plus over torquing which caused the damage
Over torque would not cause this damage as there should be nothing crushing when doing so. A bolt could fail due to that this was cased by one of two things, rod end bearing frozen causing it not to center or the two ends not being aligned causing a washer to extrude the brass. Due to the damage I think that replacement of both ends would be in order not just the one with damage as there was a reason it stuck.
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 04:12 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.