Show us your RV-14 panel

[MED]

Thanks. The throttle quadrant goes in easily, like it was designed to fit. Just had to install a couple of nut plates to secure it. I have a Thunderbolt engine with an FM-150, so had to install the supplemental cable plate and hoses. Now, I have to figure out the proper throttle and mixture cable lengths for a quadrant, since the cable plate and fittings were designed for the standard vernier cable lengths.

[mturnerb]

Originally Posted by MED

Thanks. The throttle quadrant goes in easily, like it was designed to fit. Just had to install a couple of nut plates to secure it. I have a Thunderbolt engine with an FM-150, so had to install the supplemental cable plate and hoses. Now, I have to figure out the proper throttle and mixture cable lengths for a quadrant, since the cable plate and fittings were designed for the standard vernier cable lengths.

Where did you get the quadrant?

[woodmanrog]

Here is our final design. There are 2 additional USB ports located under the bottom edge at the midpoint of the screens. These are for the data input and output of the Dynon Touch system. Turned out to be a great location as they are out of the way and don't take additional panel space. We also have Steins replacement circuit breaker panel instead of the standard auto fuses.

[MED]

The throttle quadrant is the one Van’s sells for the RV-10. You can sometimes find a builder with a new one for sale a little cheaper if they changed their installation plans.

[azflyer21]

I will be installing the HDX screens in my 14A, one item i would like to include is the separate EMS D120. I like the dedicated engine screen, that way I can use the entire PFD, MFD screens and will not have to toggle the screen to see other engine data. Any experience with the D120?

[az_gila]

Originally Posted by azflyer21

I will be installing the HDX screens in my 14A, one item i would like to include is the separate EMS D120. I like the dedicated engine screen, that way I can use the entire PFD, MFD screens and will not have to toggle the screen to see other engine data. Any experience with the D120?

Rather than adding an older Dynon D120 screen with a different interface and limited (if any) interconnection to the HDX units, why not simply add an extra 7 inch HDX screen and dedicate it to engine monitoring only?

Size is similar and that extra 1 AMU gives you a more up to date technology.

[azflyer21]

Originally Posted by az_gila

Rather than adding an older Dynon D120 screen with a different interface and limited (if any) interconnection to the HDX units, why not simply add an extra 7 inch HDX screen and dedicate it to engine monitoring only?

Size is similar and that extra 1 AMU gives you a more up to date technology.

Thanks Gil, that makes sense. I was just try to save a few $$ since I really wanted a dedicated EMS and didn't need the full EFIS.

[azflyer21]

Before committing I wanted to get feedback or suggestions on the layout These are HDX panels, thanks.

[MED]

I only see a do not enter sign.

[jeffw@sc47]

Here's the panel almost completed, the rest to be done is more of the wiring connections behind the panel.



All of the currently acquired panel instrumentation is mounted and the harness that connects everything is installed and wired to a VP-X Pro (equipment harness built by Approach Fast Stack). 'Most' everything is wired up to the common fuselage harness, still have a few days to a week to get everything connected, that is to the 97.5% done point.

In the panel equip is Garmin; a G5, a GDU465; the stack top to bottom - TO/GA button switch, GMU507, GTN650, GTR200, GMA245, an ECK ELT remote control panel above the G5; and on the right side a partially water-jetted cut out (the corners) for a GDU470 7" portrait, and I have left enough space in the right panel and behind it to put in another GDU46X if that suits me or some future owner instead of the 470. Starter, mag, and alternator (B&C 60A and a B&C 20A) switches below the G5.

Lighted rockers along the bottom for electrical items, four dimmer switches, a Hobbs, next right one of a 5 rocker switch place-holders (black snap-in cover plates), and the special 'WINGS ON / WINGS OFF' rocker switch for good measure to keep passengers thinking and to hammer in the passenger warning placard. A panel mounted dual USB port and two alternator field breakers; a few more breakers to follow as I ran out of circuit assignments in the VP-X.