VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 07-09-2018, 06:32 PM
goanddo goanddo is offline
 
Join Date: Jul 2016
Location: denver
Posts: 17
Default Center brace attachement

I just want to say up front THANK YOU to people who generously share their knowledge. I really am very grateful.

The Center cabin brace is attached to the cabin top with four screws (MS24694S72) and four spacers made from aluminum tube (AT6-058X5/16).

Here is the part I am having trouble with, the head of the screw is almost the same diameter as the spacer which is the diameter of the hole.


Screw head Diameter .351
Spacer Diameter .312
Hole diameter 5/16 .312



How does this setup hold the brace securely? Surly, I am completely missing something? Can someone please set me straight?








Thank you! Thank you!

Ron
Reply With Quote
  #2  
Old 07-09-2018, 06:51 PM
Electrogunner Electrogunner is offline
 
Join Date: Aug 2016
Location: Quarryville ,pa
Posts: 296
Default Hardware

Check the hardware call out again. I seem to remember the head of the bolt being a larger diameter. The spacer material is correct.
__________________
Donation Made For 2017
RV10 N620RV
IO540 C4B5
Whirlwind 375RV
Garmin G900X
Finishing and FWF is ongoing
Reply With Quote
  #3  
Old 07-10-2018, 06:46 AM
Lynnb's Avatar
Lynnb Lynnb is offline
 
Join Date: Jan 2014
Location: Cedar Hill, TX
Posts: 217
Default

FYI, your pictures are not showing up.
__________________
RV-10 in Process
Reply With Quote
  #4  
Old 07-10-2018, 08:01 AM
flion's Avatar
flion flion is offline
 
Join Date: Dec 2007
Location: Flagstaff, AZ
Posts: 2,489
Default

The screw head was slightly larger but I wasn't happy with the arrangement, so I chucked the spacers in a drill press and used a triangle file to make a couple of very shallow notches in the spacer and then roughed the remainder of the surface up. I then glued the spacers in, with a generous amount of epoxy and flox in the space inside the cabin top in that area. There was nothing in the instructions about gluing them in but the company often does not give explicit instructions about common procedures.
__________________
Patrick Kelley - Flagstaff, AZ
RV-6A N156PK - Flying too much to paint
RV-10 14MX(reserved) - Fuselage on gear
http://www.mykitlog.com/flion/
EAA Technical Counselor #5357
Reply With Quote
  #5  
Old 07-10-2018, 08:59 AM
ppilotmike's Avatar
ppilotmike ppilotmike is offline
 
Join Date: Jan 2010
Location: Denver, CO
Posts: 1,781
Default I am at this point also..

..Has anybody used washers or something under the heads of the screws? I seem to recall seeing an airplane with tinnerman (?sp) washers under the heads to better support the loads..
__________________
Mike Rettig
EAA Chapter 301, President www.eaa301.org
VAF Dues Current: as of 01/15/18
RV-10 (41PX Reserved) Fuselage
F-14 (Pedal Plane - Daughter's Project) "Flying"
http://www.mykitlog.com/mikrettig
Reply With Quote
  #6  
Old 07-10-2018, 01:34 PM
BobTurner BobTurner is offline
 
Join Date: Dec 2011
Location: Livermore, CA
Posts: 5,264
Default

IMHO the brace is mostly for roll over protection, when the screw will be mostly in shear and maybe compression. Forces on the small lip of the screw head should be small. I think Vansí engineering gave some thought to this design.
Reply With Quote
  #7  
Old 07-10-2018, 02:57 PM
lr172 lr172 is offline
 
Join Date: Oct 2013
Location: Schaumburg, IL
Posts: 3,008
Default

You install the al spacer flush or a bit proud of the f/g and then countersink. The 100* countersink will transition from the fiberglass and into the spacer. That countersink angle will allow the screw head to properly apply compression/tension on spacer once tightened. I wouldn't modify this, as it seems to work properly.

Larry
__________________
N64LR
RV-6A / IO-320, Flying as of 8/2015
RV-10 in progress
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 09:32 PM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.