VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 02-20-2017, 08:31 AM
pstraub's Avatar
pstraub pstraub is offline
 
Join Date: Nov 2015
Location: Galt, CA
Posts: 63
Default New Rotax Oil Tank Weeping??

Hi all, I could use some advice....I received my new Rotax from Van's a couple months ago. In preparation for the first engine start, I have been adding all the fluids, etc. I noticed a random drop of fresh oil on the floor, directly under the oil tank. It appears to be coming from these strange indentations on the bottom of the tank. I have no idea what these marks are for?? The oil is not coming from the drain plug or washer. I guess I could fill them in with pro-seal, or should I just drain the tank and get it replaced under warranty? Thanks for any thoughts...

__________________
Paul Straub, First Flight May 5, 2017
50 hours and counting.....
**2017 dues paid**
Reply With Quote
  #2  
Old 02-20-2017, 08:52 AM
TS Flightlines TS Flightlines is offline
 
Join Date: Apr 2010
Location: Ridgeland, SC
Posts: 1,909
Default

Is that where a safety wire hole is in the boss?
__________________
Tom Swearengen, TS Flightlines LLC
Teflon Hose Assemblies for Experimentals
Proud Vendor for RV1, Donator to VAF
RV7 Tail Kit Completed, Fuse started-Pay as I go Plan
Ridgeland, SC
www.tsflightlines.com
Reply With Quote
  #3  
Old 02-20-2017, 09:35 AM
pstraub's Avatar
pstraub pstraub is offline
 
Join Date: Nov 2015
Location: Galt, CA
Posts: 63
Default

Ahh, that would make sense. I guess you would safety wire the drain bolt to that? I am guessing it was cut a little too deep and punctured the threaded hole for the drain plug. Looks like I need a new oil tank?
__________________
Paul Straub, First Flight May 5, 2017
50 hours and counting.....
**2017 dues paid**
Reply With Quote
  #4  
Old 02-20-2017, 09:36 AM
DHeal DHeal is offline
 
Join Date: Sep 2006
Location: Windsor, California
Posts: 615
Default

Paul -- Those indentations are for the safety wiring of your drain plug to the oil tank. These indentations typically have small holes drilled horizontally through them for the passing of the safety wire. They certainly should not leak -- if they do, it may mean that the hole was inadvertently drilled into the fluid-holding portion of the tank. I would make sure it is in fact leaking before you drain the oil tank and inspect/test that area for a leak. If it is leaking there, that would seem to me to be a ROTAX warranty item. -- David

ps -- Always "double-wrench" that boss/plug when removing/tightening the assembly -- you might mess up the boss/tank bottom if over-torqued.
__________________
David Heal - Windsor, CA (near Santa Rosa)
EAA #23982 - EAA Technical Counselor and Flight Advisor; CFI - A&I
RV-12 E-LSA #120496 (SV w/ AP and ADS-B) - N124DH flying since March 2014 - 560+ hours (as of Oct 2017)!
VAF donation through June 2018.
Reply With Quote
  #5  
Old 02-20-2017, 09:50 AM
pstraub's Avatar
pstraub pstraub is offline
 
Join Date: Nov 2015
Location: Galt, CA
Posts: 63
Default

Thanks David, I did hold that boss with a wrench and torqued the drain plug just in case it was loose. I think the tank was compromised when they made the hole in the boss. At least now I know what I'm looking at, thanks for replies.
__________________
Paul Straub, First Flight May 5, 2017
50 hours and counting.....
**2017 dues paid**
Reply With Quote
  #6  
Old 02-20-2017, 10:59 PM
RFSchaller RFSchaller is offline
 
Join Date: Oct 2010
Location: Phoenix, AZ
Posts: 2,132
Default

A pain in the butt, but you can verify the leak by removing the tank and doing a bubble check under air pressure. If it is a manufacturing defect you should be covered by warranty.
Reply With Quote
  #7  
Old 02-21-2017, 05:38 AM
KatanaPilot KatanaPilot is offline
 
Join Date: Feb 2015
Location: Locust Grove, GA
Posts: 279
Default Here's another suggestion

Given the issues with 912's and oil changes, air in the system, purging, etc. - I would recommend you purchase an oil system purging/priming kit.

They are available from most of the Rotax parts suppliers - CPS, Lockwood, etc. I've used one for years on our 912 equipped Diamond and it helps ensure that the oil system is properly purged and primed after an oil change. You could use this to pressurize the oil tank before you drain it and check for a leak at the drain plug boss. In my opinion, you will want this kit anyway for future oil changes - go ahead and get it now for troubleshooting your current leak.
__________________
Krea Ellis

Locust Grove, GA and Miramar Beach, FL
DA20-A1 Katana "Princess Amelia"
RV-7A under construction
RV-10 under construction
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 12:54 PM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.