VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 12-09-2018, 06:13 PM
iamtheari iamtheari is offline
 
Join Date: Nov 2017
Location: ND
Posts: 280
Default Smoke oil plumbing

I am working on putting a Smoke System Helper kit into my RV-14. I figured out how to mount the oil tank (nut plates in baggage floor and seat back brace) and I have two options for the pump (mount on tank or use large adel clamps on the battery angles between the baggage bulkhead and the bell crank). But it is a mystery how best to plumb the rubber hose toward the firewall. I need to figure this out before I rivet the baggage floors into place.

Is there a safe way to use the routing clips in the tunnel? I think only three of the four are necessary for the plane (wire harness left, static hose left, wiring harness and ELT cord share one on right). So there is one spare. But it would vibrate and slice through the rubber hose if I donít protect it somehow.

I could try to route the hose through the lightening holes in the ribs and bulkheads, but to make the turns I would need adel clamps and that would also require drilling holes in the bulkheads, which for all I know could compromise the entire integrity of the airplane.

All thoughts welcome. I am stuck without anything to build and almost out of parts to prime until I figure this out.
Reply With Quote
  #2  
Old 12-10-2018, 04:21 PM
iamtheari iamtheari is offline
 
Join Date: Nov 2017
Location: ND
Posts: 280
Default

Here is my current plan, with much credit to Marvin the Smoke System Helper. I will use 3/8Ē OD aluminum tubing to go through SB750 snap bushings with rubber hose between each (the smoke system came with 3/8Ē ID hose). An elbow will point up toward the baggage floor center inspection panel next to the tank and Iíll use a quick disconnect right above the floor. The pump will mount on the tank. I would have liked to hide the pump in the tail cone but that made it too difficult to hide the hose, defeating the purpose.

The hose will run in the lower right channel. That makes oil drip directly on the bottom skin if I have to maintain it rather than dripping on wires and then the skin.

This solution maximizes maintainability and minimizes permanent weight in the airplane.
Reply With Quote
  #3  
Old 12-29-2018, 09:57 PM
DakotaHawk's Avatar
DakotaHawk DakotaHawk is offline
 
Join Date: Oct 2008
Location: Arlington, WA
Posts: 774
Default Safety: Inertia Cut-off switch

I'm cutting/pasting this response from Ron Schreck from another post on smoke oil safety.

"Following the death of Amanda Frankin in 2011 our air show team equipped our planes with an inertia switch to cut off both the electric fuel pump and the smoke oil pump. Amanda was a wing walker with her pilot husband Kyle. The engine quit and Kyle did a great job of getting the airplane down in what should have been a survivable crash. Amanda made it off the wing and into the front cockpit before they hit but was restrained by her safety tether and was severely burned in the post crash fire that was fed by the smoke oil pump. We called it the Amanda switch. I don't fly air shows and don't use smoke oil any more but I keep the inertia switch wired in line with the electric fuel pump, just in case.

This is the one we use: https://www.pegasusautoracing.com/pr...0aAl-2EALw_wcB "
__________________
_______________________________
Scott "Grumpy" Stewart
RV-7 N957RV (First Flight on Dec 18, 2009)
RV-14 N144P (Empennage complete, wings almost complete, fuselage almost complete)
#866 on the Van's RV-7 hobbs
#6563 on Van's generic hobbs
Arlington, WA
Reply With Quote
  #4  
Old 12-30-2018, 08:45 AM
Jpm757 Jpm757 is offline
 
Join Date: May 2013
Location: Sherman, CT
Posts: 344
Default

Fuel pump inertia switch-great idea! My next mod!
__________________
Jake
RV6 #20477 completed 1991 sold.
RV7 #72018 N767T first flight 11/21/2017 200+ hrs.
IO-360M1B MT 3 blade, Dual AFS 5600 QUICK Panel.
KOXC Oxford, CT
1941 J3 Cub skis,floats.
2019 dues gladly paid.
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 06:45 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.