VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics


Go Back   VAF Forums > Search Forums
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Showing results 1 to 62 of 500
Search took 0.07 seconds.
Search: Posts Made By: Jesse
Forum: Electrical Systems Today, 01:07 PM
Replies: 7
Views: 760
Posted By Jesse
If you have a single impulse coupling, then...

If you have a single impulse coupling, then install the jumper between the Right position on the key switch and the Gnd position right next to it. This will kill your right mag during start so your...
Forum: RV General Discussion/News Today, 07:13 AM
Replies: 27
Views: 3,452
Posted By Jesse
If you are using a VP-X, it will allow preset...

If you are using a VP-X, it will allow preset flap positions based on the input from the position sensor.
Forum: ADS-B Today, 07:09 AM
Replies: 7
Views: 206
Posted By Jesse
It should have no problem interfacing with the...

It should have no problem interfacing with the GDL82. Everything the transponder sends out still gets sent out. The GDL82 is a different frequency band anyway, and they will just get 2 forms of your...
Forum: Electrical Systems Today, 06:47 AM
Replies: 4
Views: 281
Posted By Jesse
Ok, so it may work if you leave the red...

Ok, so it may work if you leave the red disconnected and ground the black, then run the two whites to 3 & 4 on the relay. If you power the red and ground the black, then run them to pins 11 and 12 on...
Forum: VAF Classifieds (posts in here deleted after 30 days) Today, 06:42 AM
Replies: 3
Views: 316
Posted By Jesse
I have collected several of these. If anybody is...

I have collected several of these. If anybody is interested, I can do $200 shipped CONUS.
Forum: VAF Classifieds (posts in here deleted after 30 days) Today, 06:38 AM
Replies: 26
Views: 5,103
Posted By Jesse
Youíd be amazed what I have seen that passed an...

Youíd be amazed what I have seen that passed an airworthiness inspection, and even by a so-called reputable DAR. Itís scary sometimes. As others have said, some DARís, in my experience, say, ďhmm,...
Forum: RV-8/8A Today, 06:35 AM
Replies: 3
Views: 246
Posted By Jesse
There are usually horizontal pins holding the top...

There are usually horizontal pins holding the top cowl onto the bottom cowl. If you can see a pin on the front sides of the cowl, remove the screw and pull the pin. Sometimes there is a decorative...
Forum: Autopilots Today, 06:32 AM
Replies: 4
Views: 161
Posted By Jesse
Pin 17 on the TruTrak should be getting serial...

Pin 17 on the TruTrak should be getting serial (RS232) data from the gps. From the manual:

Primary Serial Input. Baud rate selectable 1200, 2400, 4800 or 9600 baud. Automatically decodes NMEA-0183,...
Forum: Electrical Systems Yesterday, 05:46 PM
Replies: 4
Views: 281
Posted By Jesse
Your picture is not displaying. THe red gets...

Your picture is not displaying. THe red gets aircraft power and the Black gets aircraft ground. The two whites go to the trim servo. If you are using a relay, then Iím not exactly sure how it would...
Forum: RV-12 02-20-2018, 09:18 PM
Replies: 4
Views: 497
Posted By Jesse
I have seen this problem with a bad auto pilot...

I have seen this problem with a bad auto pilot servo, but usually it is a network cable that is not working correctly. Go into the settings and then to network status and see what devices are showing...
Forum: RV-12 02-19-2018, 09:51 PM
Replies: 93
Views: 14,676
Posted By Jesse
I just sent you an email with the pinout chart.

I just sent you an email with the pinout chart.
Forum: VAF Classifieds (posts in here deleted after 30 days) 02-19-2018, 07:00 PM
Replies: 2
Views: 557
Posted By Jesse
AP74 sold. HS34 still available.

AP74 sold. HS34 still available.
Forum: VAF Classifieds (posts in here deleted after 30 days) 02-19-2018, 04:43 PM
Replies: 0
Views: 487
Posted By Jesse
Panel Design and Cutting Services Offered

I have recently purchased a new panel cutting CNC. I will be providing this service to the RV community to design, cut, bend (if desired) and ship panels, as well as powder coating and possibly...
Forum: Reviews 02-19-2018, 06:12 AM
Replies: 4
Views: 696
Posted By Jesse
Youíre welcome any time, George.

Youíre welcome any time, George.
Forum: Electrical Systems 02-19-2018, 06:11 AM
Replies: 7
Views: 305
Posted By Jesse
Most Plane Power alternators have two wires...

Most Plane Power alternators have two wires coming from the unit, a red for field that connects to two pins as you describe, then a white from the third point that offers ground if the alternator...
Forum: Reviews 02-18-2018, 09:16 PM
Replies: 4
Views: 696
Posted By Jesse
Jim, it was my pleasure working with you and John...

Jim, it was my pleasure working with you and John this week. I know it was a frustrating 2 days, but it was great getting to know the two of you. Stop by any time youíre in the area.
Forum: RV General Discussion/News 02-18-2018, 09:13 PM
Replies: 9
Views: 326
Posted By Jesse
Whatís is your altitude encoder source? What else...

Whatís is your altitude encoder source? What else is in your panel? If you have a GTN gps, it controls the transponder and gives the altitude to it as well. If it is getting the altitude via RS232...
Forum: Glass Cockpit 02-18-2018, 07:42 PM
Replies: 22
Views: 966
Posted By Jesse
What to leave would be determined by your mission...

What to leave would be determined by your mission and trust in the GRT system. As for engine gauges, I have never tried to run two systems off of one sender, but I am sure some would work and others...
Forum: Glass Cockpit 02-18-2018, 07:36 PM
Replies: 33
Views: 2,581
Posted By Jesse
No offense, but it has been determined that they...

No offense, but it has been determined that they have a bug this significant. I do hope they come out with a fix fast. I will leave my response to this.....
Forum: Glass Cockpit 02-18-2018, 06:16 PM
Replies: 33
Views: 2,581
Posted By Jesse
Please post the instructions.

Please post the instructions.
Forum: Glass Cockpit 02-18-2018, 12:14 PM
Replies: 33
Views: 2,581
Posted By Jesse
It sounds like the problem is appearing in...

It sounds like the problem is appearing in multiple installations. We were told that we probably have a CAN bus proplem by Garmin tech support. We have probably 30-50 man hours into troubleshooting...
Forum: RV-6/6A 02-18-2018, 11:28 AM
Replies: 2
Views: 462
Posted By Jesse
Email me a picture of your pitot tube. Getting...

Email me a picture of your pitot tube. Getting water in the pitot will not necessarily kill the system, and it is a pressure system with no air actually flowing through. It will kill it, but water...
Forum: Glass Cockpit 02-18-2018, 11:24 AM
Replies: 33
Views: 2,581
Posted By Jesse
I spent 2 full days troubleshooting this exact...

I spent 2 full days troubleshooting this exact problem this week with the same version of software. It sounds like we have a software bug!
Forum: RV General Discussion/News 02-14-2018, 06:03 AM
Replies: 3
Views: 446
Posted By Jesse
I agree completely that you should do Option 1...

I agree completely that you should do Option 1 and 2, in that order. I have sold several planes with the VP200 installed, and that hasnít affected the sale. Personally, I would have no problem buying...
Forum: Florida (North) 02-12-2018, 05:04 PM
Replies: 6
Views: 381
Posted By Jesse
Why donít you fly directly into Destin?

Why donít you fly directly into Destin?
Forum: Temp / Test / Misc. (posts deleted after 2 weeks) 02-11-2018, 09:46 PM
Replies: 9
Views: 343
Posted By Jesse
I can loan you one if thereís an easy way to get...

I can loan you one if thereís an easy way to get it to and from.
Forum: VAF Classifieds (posts in here deleted after 30 days) 02-11-2018, 08:03 AM
Replies: 0
Views: 158
Posted By Jesse
WTB: RV-12 Empenage Kit

Iím in need of an RV-12 empennage kit. If anybody has decide building isnít for you, please let me know.
Forum: VAF Classifieds (posts in here deleted after 30 days) 02-11-2018, 07:49 AM
Replies: 2
Views: 557
Posted By Jesse
Prices dropped.

Prices dropped.
Forum: VAF Classifieds (posts in here deleted after 30 days) 02-09-2018, 04:14 PM
Replies: 2
Views: 176
Posted By Jesse
I have one without the wiring harness, but it...

I have one without the wiring harness, but it would be easy to make one up. $250 shipped CONUS. New price is $529.
Forum: RV General Discussion/News 02-09-2018, 04:06 PM
Replies: 23
Views: 2,460
Posted By Jesse
I have provided the "middle man" service in the...

I have provided the "middle man" service in the past and am happy to do that again. Basically, the item would be shipped to me once a price has been agreed upon. I can test to make sure it works if I...
Forum: VAF Classifieds (posts in here deleted after 30 days) 02-09-2018, 04:02 PM
Replies: 2
Views: 557
Posted By Jesse
FS: Dynon HS34 & AP74

I have just removed a Dynon HS34 and AP74. They are both horizontal. They will include the mounting bracket but no harnesses.

HS34 $400 shipped CONUS

AP74 $300 shipped CONUS
Forum: RV General Discussion/News 02-09-2018, 07:25 AM
Replies: 11
Views: 801
Posted By Jesse
Most trade shows, including SNF and Oshkosh,...

Most trade shows, including SNF and Oshkosh, require that you charge sales tax on any sales at the show that deliver at the show. Any company that doesnít is breaking FL law. That doesnít mean that...
Forum: RV-7/7A 02-09-2018, 07:19 AM
Replies: 5
Views: 353
Posted By Jesse
Does just your gauge change rpm, or do you...

Does just your gauge change rpm, or do you feel/hear the fluctuations! If it is actually changing rpm, call MT and tell them that and they will put in a heavier spring (this used to be a common issue...
Forum: RV General Discussion/News 02-09-2018, 07:10 AM
Replies: 11
Views: 801
Posted By Jesse
As Bob said, few vendors take product like this...

As Bob said, few vendors take product like this to the show. And yes, if you take delivery in FL you pay sales tax. If you place an order for them to ship to you, then you can pay at the show and...
Forum: RV General Discussion/News 02-09-2018, 07:08 AM
Replies: 22
Views: 1,992
Posted By Jesse
+1 from me too.

+1 from me too.
Forum: Glass Cockpit 02-07-2018, 05:56 PM
Replies: 5
Views: 454
Posted By Jesse
I think it will do all you are askin, but I think...

I think it will do all you are askin, but I think you would be much happier and much more feature rich if you installed a Garmin auto pilot with a GMC307 controller. The Stec should be worth...
Forum: Safety 02-06-2018, 05:52 PM
Replies: 8
Views: 525
Posted By Jesse
Search for the booklet printing settings. It...

Search for the booklet printing settings. It should be able to print in the way you want.
Forum: Southeast 02-05-2018, 05:51 PM
Replies: 5
Views: 615
Posted By Jesse
Are you giving me N256H back?

Are you giving me N256H back?
Forum: Places To Fly...Things to See...Things to Eat 02-03-2018, 08:38 PM
Replies: 7
Views: 496
Posted By Jesse
We are about a 1.5-2hr drive from Daytona. If you...

We are about a 1.5-2hr drive from Daytona. If you fly into X35 Iíll put you in the hangar and lend you my car for the weekend. If you canít find a closer hotel, you can stay in the RV Hotel here.
Forum: Nosewheel vs. Tailwheel 02-03-2018, 02:48 PM
Replies: 17
Views: 2,950
Posted By Jesse
I don’t think I have pictures, but I am aware of...

I don’t think I have pictures, but I am aware of at least 2 cases where the nose job was not sufficient to prevent a nose over. If you try hard enough you can break anything.
Forum: VAF Classifieds (posts in here deleted after 30 days) 02-02-2018, 02:26 PM
Replies: 0
Views: 200
Posted By Jesse
FS: KT76C w/ Harness and Encoder

I have a KT76C with harness and Ameri-King encoder that was working when removed. $400 shipped CONUS.

Prefer E-mail, Phone or Text.
Forum: Traditional Aircraft Engines 02-01-2018, 09:50 PM
Replies: 7
Views: 1,383
Posted By Jesse
A flat head screw driver and a mallet is what I...

A flat head screw driver and a mallet is what I use, gently.
Forum: Glass Cockpit 02-01-2018, 09:49 PM
Replies: 9
Views: 846
Posted By Jesse
Itís just like talking. One ear can only listen...

Itís just like talking. One ear can only listen to one voice at a time, but one voice can be heard by many ears at the same time. One output can talk to many inputs, but one input can only accept one...
Forum: VAF Classifieds (posts in here deleted after 30 days) 02-01-2018, 09:40 PM
Replies: 4
Views: 280
Posted By Jesse
I think I have one. May have backplate and...

I think I have one. May have backplate and connectors too. Call me tomorrow and Iíll check the shelf.
Forum: Fuel Injection Systems 02-01-2018, 07:20 AM
Replies: 11
Views: 791
Posted By Jesse
The heat soak happens when you shut down the...

The heat soak happens when you shut down the engine and let all of the exhaust and engine heat just sit idle in the cowl and heat everything up. A long taxi would help to cool the engine, possibly,...
Forum: RV-14 02-01-2018, 07:16 AM
Replies: 4
Views: 576
Posted By Jesse
It should be for an ASEL clamp holding the...

It should be for an ASEL clamp holding the plastic rudder Cable sleeve in place so the Cable doesnít rub on the tunnel side.
Forum: Glass Cockpit 02-01-2018, 07:14 AM
Replies: 9
Views: 846
Posted By Jesse
Go into the G3X configuration and see if you see...

Go into the G3X configuration and see if you see the G5 with a green check mark. You need to give the existing MAPMX line going to the G3X a parallel line to the G5 as well.
Forum: COMM 02-01-2018, 07:10 AM
Replies: 9
Views: 416
Posted By Jesse
Technically, the 2020 gps is strictly VFR and is...

Technically, the 2020 gps is strictly VFR and is just a position source for your transponder. It certainly is not legal as an IFR Nav source, even if just using it for DME.
Forum: RV General Discussion/News 01-31-2018, 07:50 PM
Replies: 1
Views: 363
Posted By Jesse
Garmin GDL82 with external source

I helped troubleshoot an installation of a GDL82 in a Bonanza today. It is wired to a GNS530W. The manual says how to wire it and it is wired correctly, but it doesnít say how to configure the 530...
Forum: RV-12 01-31-2018, 07:36 PM
Replies: 20
Views: 3,745
Posted By Jesse
But isnít that exactly what the Light Sport rules...

But isnít that exactly what the Light Sport rules were? No more medical required. Easier certification.

Even though basicmed was a law, it also did much the same thing.
Forum: COMM 01-30-2018, 09:12 PM
Replies: 9
Views: 416
Posted By Jesse
They no longer recommend using the Dynon Intercom...

They no longer recommend using the Dynon Intercom for 2 COM radios. I would certainly keep your GMA340. You can make it all work with switches, but that is far from ideal, and you will need to also...
Forum: RV General Discussion/News 01-30-2018, 05:47 PM
Replies: 9
Views: 669
Posted By Jesse
It have seen the. Go bad, but reading Low then...

It have seen the. Go bad, but reading Low then reading High doesnít make sense for a failing sensor. If 14 would be normal fuel flow, then dropping out periodically could be a bad wire connection or...
Forum: VAF Classifieds (posts in here deleted after 30 days) 01-30-2018, 05:28 PM
Replies: 2
Views: 368
Posted By Jesse
Email sent.

Email sent.
Forum: VAF Classifieds (posts in here deleted after 30 days) 01-29-2018, 08:39 PM
Replies: 14
Views: 1,954
Posted By Jesse
I have a -6A that will be going up for sale in...

I have a -6A that will be going up for sale in the next week days. Iím waiting to pick it up so I can get pictures and details.
Forum: Engine Monitors 01-29-2018, 07:12 AM
Replies: 7
Views: 342
Posted By Jesse
https://www.aircraftspruce.com/catalog/inpages/grt...

https://www.aircraftspruce.com/catalog/inpages/grt-hps-01.php?clickkey=5966here is a link to the 1-80psi sensor.
Forum: Engine Monitors 01-28-2018, 09:38 PM
Replies: 7
Views: 342
Posted By Jesse
Iím sure I have a used one in stock, but I would...

Iím sure I have a used one in stock, but I would highly recommend you move to the Kavlico sender. It takes a little extra wiring, but itís worth it. Dynon and AFS donít sell the VDOís any more, Iím...
Forum: RV General Discussion/News 01-28-2018, 02:40 PM
Replies: 3
Views: 335
Posted By Jesse
I agree. Mounting square on the sub panel should...

I agree. Mounting square on the sub panel should work fine.
Forum: Rocket 01-28-2018, 08:13 AM
Replies: 18
Views: 1,738
Posted By Jesse
https://www.dropbox.com/s/nzl8i7lw1lpymim/Bill%20W...

https://www.dropbox.com/s/nzl8i7lw1lpymim/Bill%20Whidden%20Rocket%20Panel%20Draft%201%208-16-2017.pdf?dl=0
Forum: RV-4 01-28-2018, 07:57 AM
Replies: 5
Views: 586
Posted By Jesse
I have installed one near the front stick, IIRC....

I have installed one near the front stick, IIRC. I used the bolt holding the right wing pushrod, lengthened it and put a spacer to hold the servo pushrod. You may need to slightly enlarge the...
Forum: Rocket 01-28-2018, 07:55 AM
Replies: 18
Views: 1,738
Posted By Jesse
I have installed a panel similar to this in a...

I have installed a panel similar to this in a rocket, IIRC. Email me and Iíll see if I have a PDF of the layout.
Forum: RV-10 01-28-2018, 07:42 AM
Replies: 8
Views: 440
Posted By Jesse
Not all parts Vanís sells are on their online...

Not all parts Vanís sells are on their online store.
Forum: Glass Cockpit 01-27-2018, 07:05 PM
Replies: 1
Views: 235
Posted By Jesse
Does it only happen in Flight? If on the ground...

Does it only happen in Flight? If on the ground also, run a new wire outside the plane and see if it goes away. If only in Flight, move it into the cabin and Velcro more or less level and pointing...
Showing results 1 to 62 of 500

 
Forum Jump

All times are GMT -6. The time now is 08:44 PM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.