VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics


Go Back   VAF Forums > Search Forums
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Showing results 1 to 62 of 500
Search took 0.07 seconds.
Search: Posts Made By: JBPILOT
Forum: RV-12 10-10-2018, 05:59 AM
Replies: 7
Views: 613
Posted By JBPILOT
Just my thoughts - -

It is fast and easy to take the top off the tank. A thin blade scraper and a hammer will take the top off in about 5 mins after you drill out the old rivets. Work from the corners to the center of...
Forum: RV-12 10-02-2018, 05:53 AM
Replies: 20
Views: 1,436
Posted By JBPILOT
I did mine - -

Since you don't know where the trim should be set for sure, be very sure it is working properly before actual first flight. You will need to adjust it once the wheels come off the runway. First...
Forum: RV-12 09-23-2018, 06:23 AM
Replies: 17
Views: 1,680
Posted By JBPILOT
Tom O - - -

Flew yesterday a couple hundred miles with our group. Still running the same as when new. Sucks down terrible amounts of oil. So bad, that it will use over a pint in 100 hours ! ! ! ! ! Great...
Forum: RV-12 09-22-2018, 05:59 AM
Replies: 17
Views: 1,680
Posted By JBPILOT
Since 'new' - -

Oct 2009 = 1,254.3 hours.
Forum: RV-12 09-06-2018, 06:27 AM
Replies: 13
Views: 2,673
Posted By JBPILOT
Steve- -

When mine failed last time, it did the same as yours. Indicator went to bottom. If it was working at some point, then you just need better connections at the connector(s). There is enough wire...
Forum: RV-12 09-05-2018, 08:40 PM
Replies: 13
Views: 2,673
Posted By JBPILOT
Wire crimping - -

is the likely issue. I have done mine maybe 3 times in 9 years. Those tiny wires are hard to get perfect crimps. I went against the instructions and soldered mine this year. Works perfect now. ...
Forum: ADS-B 08-24-2018, 02:36 PM
Replies: 18
Views: 2,055
Posted By JBPILOT
Me too - -

Last week I had one at 1570 kts at 25,000'. Not on screen long for sure.
Forum: Traditional Aircraft Engines 08-08-2018, 08:59 AM
Replies: 10
Views: 781
Posted By JBPILOT
Just a note - -

The other style flow sensor I have been able to get working again with instructions from the vendor. Take it out and fill it half full of CARB CLEANER, and shake it a bunch and wash it out with gas...
Forum: RV-12 08-06-2018, 06:17 AM
Replies: 135
Views: 18,001
Posted By JBPILOT
Jim - -

Did you take pic of it. Look any different ? Thanks.
Forum: ADS-B 07-30-2018, 01:06 PM
Replies: 227
Views: 32,580
Posted By JBPILOT
Spoke with Uavionix at OSH - -

They said only one person has sent data for them to look at regarding dropping targets. For those waiting for an update, it may not happen unless they get more data. If the info they gave me is...
Forum: RV General Discussion/News 07-05-2018, 12:10 PM
Replies: 13
Views: 2,059
Posted By JBPILOT
Another idea - -

I have had a problem with the other version. I spoke to mfgr. A good tech said to remove it and fill it half full of carb cleaner and shake the snot out of it and then blow out with low pressure. ...
Forum: RV-10 06-09-2018, 05:46 PM
Replies: 36
Views: 3,733
Posted By JBPILOT
My experience - -

I have the Flow-Scan. I called the factory, and a great guy said to : " Take it out and put Carb cleaner in it and shake it for a minute, then wash it out with gas or another fluid " It worked. ...
Forum: RV-12 05-31-2018, 08:22 PM
Replies: 18
Views: 3,816
Posted By JBPILOT
Even more comments - -

Try to get a ride with a very experienced RV-12 pilot. It flies much better with two in it, but you will get the idea if it is gusty and more than 15kts.
Forum: RV-12 05-31-2018, 04:34 PM
Replies: 18
Views: 3,816
Posted By JBPILOT
More comments - -

The RV-12 is light enough, that just about the time you think you are going to touch down, a slight puff of wind will have you back up - and quickly. I have developed the habit of taking the flaps...
Forum: RV-12 05-31-2018, 11:58 AM
Replies: 18
Views: 3,816
Posted By JBPILOT
My experience - -

With an RV-12 - work your way up very slowly until you know where you are comfortable. A 10kt 90 degree crosswind can be a real surprise in a very light plane. I have over 1,200 hours in my RV-12....
Forum: RV-12 05-21-2018, 10:41 AM
Replies: 8
Views: 1,569
Posted By JBPILOT
At a quick glance - -

Looks like you could bend the spring connection loop closer to the exhaust and gain some clearance.
Forum: RV-12 05-04-2018, 08:32 AM
Replies: 11
Views: 2,074
Posted By JBPILOT
Questions - -

When sitting on the ground, what is the flow reading with elec pump on and off ?
Forum: RV General Discussion/News 05-03-2018, 08:58 PM
Replies: 9
Views: 1,161
Posted By JBPILOT
IPad Pro Sunlight

http://i63.tinypic.com/2qch6rk.jpg

I have been satisfied with the IPad Pro. Can read it as well as the other displays
Forum: RV-12 04-17-2018, 04:54 PM
Replies: 11
Views: 1,978
Posted By JBPILOT
Robert - -

Good to hear how others live. I guess with that, I appreciate that part of my area. We have another snow storm for tonight and tomorrow. I would give up a few airports for some better weather...
Forum: RV-12 04-17-2018, 03:48 PM
Replies: 11
Views: 1,978
Posted By JBPILOT
Thanks Scott - -

I am the Flyout Coordinator for our EAA chapter in Waterloo, Iowa. I schedule about 75 Flyouts per year. Most are less than 125 miles one way. It is some work for me, but I get as much enjoyment...
Forum: RV-12 04-17-2018, 01:35 PM
Replies: 11
Views: 1,978
Posted By JBPILOT
MILESTONE - today

http://i66.tinypic.com/2r5sqci.jpg

Still running very well.
Forum: RV-12 03-26-2018, 12:02 PM
Replies: 8
Views: 2,360
Posted By JBPILOT
Some experience with these issues - -

I would start with taking the rear floor tunnel covers off. ( yes, may be lots of work if tank has to be removed ). I worked on one that had been set up completely wrong. If you have the builder...
Forum: RV-12 03-07-2018, 07:40 AM
Replies: 5
Views: 885
Posted By JBPILOT
THANKS Dave - -

When any issues come up, I would like to have a spare D-180 mother board to look at, at home, before having to remove and take back to the airport and try it again. I have had 3 - 4 times that it...
Forum: RV-12 03-05-2018, 05:57 AM
Replies: 163
Views: 35,048
Posted By JBPILOT
Hmmm --

Don't think you could. Solid squeezed rivets would be hard to do. Flange to rivet to would still be there. I better say no you can't. Having smaller hands will help. Just not a fun job.
Forum: RV-12 03-04-2018, 12:54 PM
Replies: 163
Views: 35,048
Posted By JBPILOT
ME TOO - -

Just finished an hour ago. Was able to pull on cable enough to get hooked up again. Not easy, but doable. Agree, it certainly strengthened the hinges. Getting the two main bolts back in is not...
Forum: RV-12 02-09-2018, 12:29 PM
Replies: 19
Views: 2,879
Posted By JBPILOT
Same here - -

Right Front top of cyl, coolant elbow 'O' ring.
Forum: RV-12 01-25-2018, 09:11 AM
Replies: 37
Views: 6,287
Posted By JBPILOT
Oil Therm Testing

https://youtu.be/BF_uqyqRJRg

My 205 Thermostassis element was getting tired I think. I installed a new one. Sorry about the video. Hard to fly and hold a phone etc. It is again working like it...
Forum: RV-12 01-16-2018, 12:00 PM
Replies: 26
Views: 5,118
Posted By JBPILOT
Sorry - -

Should have said 'C' clamp. Likely better understood.
Forum: RV-12 01-15-2018, 06:18 PM
Replies: 26
Views: 5,118
Posted By JBPILOT
Another method - -

If you clamp a 2" screw clamp on each spar and use a tie-down or such to draw them together it works well and no pounding on pins.
Forum: RV-12 01-12-2018, 04:13 PM
Replies: 9
Views: 1,507
Posted By JBPILOT
This works well - -

http://i68.tinypic.com/29yob5y.jpg

I put this on several years ago. RTV about every 6" on inside. Can remove easy.
Forum: RV-12 12-25-2017, 04:15 PM
Replies: 9
Views: 2,340
Posted By JBPILOT
Just a thought - -

If you are at 80kts, they will be stiff until you get down to say 65 kts. They should move easier as you slow down.
Forum: RV-12 12-13-2017, 04:24 PM
Replies: 150
Views: 23,785
Posted By JBPILOT
Justy asking - -

Did you take a sample of the fuel to an independent analyzer to verify it was at least 91 ?
Forum: RV-12 12-09-2017, 10:41 AM
Replies: 37
Views: 6,287
Posted By JBPILOT
Scott - -

If throttle is greatly reduced in cold, very cold, weather, the temps will back back down until the therm opens up and no oil goes thru the cooler. In moderate or warm weather, it will not change as...
Forum: RV-12 12-09-2017, 10:06 AM
Replies: 37
Views: 6,287
Posted By JBPILOT
Joe - -

No reason to. Oil in the tank is approx. therm value, and that is all that is important. Agree, your test could warm up the oil at then engine, but it is just not important.
Forum: RV-12 12-09-2017, 05:59 AM
Replies: 37
Views: 6,287
Posted By JBPILOT
Scott - -

Power demand is an important factor. Notice I was not demanding much power, so less warm oil was involved with the blending on return, and oil going even slower thru the cooler makes the blend even...
Forum: RV-12 12-08-2017, 06:03 PM
Replies: 37
Views: 6,287
Posted By JBPILOT
Scott - -

Thanks for being involved. I can tell you for sure that even in 4 degree F temps, the oil gets up to therm value as indicated on the display before closing some and then blending the return oil and...
Forum: RV-12 12-08-2017, 12:40 PM
Replies: 37
Views: 6,287
Posted By JBPILOT
Scott - -

You likely do not get to, or want to, fly in very cold weather, but here is what happens. Even in cold weather the 98% bypass Thermostasis directs almost all oil thru therm back to engine, with...
Forum: RV-12 12-08-2017, 10:52 AM
Replies: 37
Views: 6,287
Posted By JBPILOT
Joe - -

INITIAL NOTE : The Thermostasis unit is considered a 98% bypass. Not at all like the automotive designs which are considered 10% bypass.

The Therm forces oil to go thru the cooler when the desired...
Forum: RV-12 12-07-2017, 08:23 PM
Replies: 37
Views: 6,287
Posted By JBPILOT
Will try - -

I don't believe Rotax needs the oil at the spec temp going into the engine, just need it to warm up at some point to stop moisture build up. They want the oil at 122F to take off at WOT, so 153 is...
Forum: RV-12 12-07-2017, 03:11 PM
Replies: 37
Views: 6,287
Posted By JBPILOT
Yes - - -

Another design of mine. Many call it the "Bender Baffle". That is why I can fly comfortably, even at 4 degrees outside temp. Nice warm air comes from the rad. by forcing the temps up, and slowing...
Forum: RV-12 12-07-2017, 12:37 PM
Replies: 37
Views: 6,287
Posted By JBPILOT
GOOD EXAMPLE TODAY - - - -

Was about 4 degrees F at Alt today. I have Thermostasis. Oil temp at engine was 153 degrees on display. NO PROBLEM. Oil in tank is between 195 - 205 degrees. Very cold oil from cooler was...
Forum: RV-12 12-06-2017, 07:19 PM
Replies: 37
Views: 6,287
Posted By JBPILOT
Will try to answer oil temps -

Rotax wants the oil to be at that temp to keep water from forming in the system. If you have a Thermostasis, then the oil is getting into a needed temp range IN THE TANK. Since your display is...
Forum: RV-12 12-06-2017, 11:58 AM
Replies: 37
Views: 6,287
Posted By JBPILOT
COMMENTS ONLY - -

If you use a Thermostasis Oil Therm, your oil is good. It is confusing, but the temp we see on the display is the oil temp at the engine, not the tank. The "Bender Baffle" as some call it, has been...
Forum: ADS-B 11-28-2017, 09:52 AM
Replies: 227
Views: 32,580
Posted By JBPILOT
Alan and others - -

My GPS antenna is on the shelf under the top cowl where the original XM antenna was designed to go. A short provided adapter cable allowed me to keep both antennas from previous setup. I have had...
Forum: RV-12 11-26-2017, 06:38 AM
Replies: 41
Views: 6,584
Posted By JBPILOT
Test pic site - -

http://i67.tinypic.com/2elxoxd.jpg

Still testing
Forum: RV-12 11-26-2017, 06:36 AM
Replies: 41
Views: 6,584
Posted By JBPILOT
What I do - -

I bought a smaller aluminum platform to stand on. I built a funnel that fits tight into filler neck. I can dump 5 - 6 gallons in less than a minute. Makes it much easier. Will try to get new pic...
Forum: ADS-B 11-24-2017, 07:28 AM
Replies: 227
Views: 32,580
Posted By JBPILOT
Ron - - - -

I bought their GPS combo package. Two very small boxes that you can mount nearly anywhere. They provided an 'adapter' short wire to change from GPS antenna I had to their small snap in type...
Forum: ADS-B 11-23-2017, 10:09 AM
Replies: 227
Views: 32,580
Posted By JBPILOT
My experience so far - -

Excellent. Got back perfect report first time. I was using the Navworx EXP, so reused my out antenna and GPS antenna. Simple and fast. Like receiving both 1090 & 978 in.
Forum: ADS-B 11-07-2017, 01:21 PM
Replies: 227
Views: 32,580
Posted By JBPILOT
OPTION 1 - -

Very short adapter cable.
Forum: ADS-B 11-06-2017, 03:11 PM
Replies: 227
Views: 32,580
Posted By JBPILOT
Satisfied Customer Report - -

I removed the EXP, and installed the UAvionix UAT & GPS source combo. I was provided an adapter to go from GPS antenna I had to smaller hookup on their GPS source. I was able to re-use the output...
Forum: ADS-B 11-06-2017, 05:49 AM
Replies: 703
Views: 200,902
Posted By JBPILOT
Got my report day one - -

3 3 3 3 3 ( for enough info )
Forum: RV-12 10-28-2017, 09:39 AM
Replies: 7
Views: 1,487
Posted By JBPILOT
INTERESTING THOUGHTS - -

I actually like to take off with the takeoff trim set the same as landing. I just look to see the trim indicator is lined up and go. Yes, you need to trim down shortly after takeoff, but I guess...
Forum: RV-12 10-26-2017, 07:49 AM
Replies: 146
Views: 32,751
Posted By JBPILOT
Jim and others - -

I run the coax under the arm rest, behind the gas tank, into tail section. The GPS receiver I mounted on same original plate as XM receiver would have been mounted, beside Garmin receiver. This...
Forum: RV-12 10-26-2017, 06:12 AM
Replies: 146
Views: 32,751
Posted By JBPILOT
ECHO UAT - -

Forgot you asked about where output Antenna is mounted. From the Navworx install, I have it under side near first rib of tail. About 5' from original TXP Antenna. They provided a new one, but I...
Forum: RV-12 10-26-2017, 06:02 AM
Replies: 146
Views: 32,751
Posted By JBPILOT
ECHO UAVIONIX Install - -

http://i63.tinypic.com/29ghblu.jpg

I have a very early RV-12 w/D-180. I had the Navworx mounted on top of the map box. I removed and installed the two new boxes as shown. The antenna hooked up to...
Forum: RV-12 10-25-2017, 06:02 PM
Replies: 146
Views: 32,751
Posted By JBPILOT
ECHO UAVIONIX report - -

I received a new ECHO UAT and GPS source from UAVIONIX today. Installed this afternoon, and did setup, then flew, and got back what I think is an excellent report from the FAA site. At this point -...
Forum: RV-12 10-21-2017, 07:19 AM
Replies: 146
Views: 32,751
Posted By JBPILOT
BIG JOHN - -

http://i68.tinypic.com/30kdmxt.jpg

Hope this helps. I have been very happy with this setup in same model and age plane. I have ADS-B feeding it. With new IPad Pro, you can read it in direct...
Forum: RV-12 10-19-2017, 06:24 AM
Replies: 26
Views: 5,460
Posted By JBPILOT
Vern - -

That's what they are supposed to do. Springs pull to open.
Forum: RV-12 10-18-2017, 03:04 PM
Replies: 22
Views: 2,737
Posted By JBPILOT
What I do - -

Drain tank. Use crows foot wrenches to loosen and remove both lines on bottom after removing both rear inspection plates. Take screws from filler neck out. Twist as needed to remove filler neck. ...
Forum: RV-12 10-08-2017, 06:16 AM
Replies: 13
Views: 3,051
Posted By JBPILOT
Big John - -

If the original drilling of the torque tubes were not correct, you can not adjust it out. You could buy one side or the other and make them match. What Bob said above would be best. Put the...
Forum: RV-12 10-07-2017, 01:43 PM
Replies: 13
Views: 3,051
Posted By JBPILOT
Curious - -

With rear most baggage floor plate off, are arms in equal position when flaps appear to be in proper position for level flight ?
Forum: RV-12 10-06-2017, 05:51 AM
Replies: 8
Views: 2,125
Posted By JBPILOT
Ok so far - -

http://i64.tinypic.com/16jo806.jpg

1,130 hours. Try not to bounce it. I don't see even a tiny crack, so will just check it.
Showing results 1 to 62 of 500

 
Forum Jump

All times are GMT -6. The time now is 11:09 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.